Regardless it’s for your personal security, for roadworthiness testing or to avoid a fine, being certain your headlamp bulbs are always effective is necessary. In fact, bulbs are wearing parts that will undoubtedly burn out in the future and as a result need to be changed. You’re most certainly on the website because one of your parking lights is burnt out and you’re questioning how to change your Ford Edge’s license plate bulb, we’ve written this article to help you do it without any help and not have to go to your mechanic. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Ford Edge.
How to change the license plate bulb on your Ford Edge throughout the outside
This process is the most simple of the two, in reality, for this one you will only have to remove the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the situation we will dedicate a moment on in the second part of this document to demonstrate the approach.
So let’s start with replacing the number plate bulb by going through the outside of your Ford Edge. Regardless it’s the front or the back of your car the procedure will be the same.
Here are a few simple guidelines to stick to to carry out this routine service:
- With the engine off, disconnect the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch specified for this purpose (almost always on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Ford Edge
- Use your screwdriver or knife to eject the bulb from its place, in the event you are afraid of damaging anything, you can also do it with your fingers.
- Finally, put the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and test the light to validate the successfulness of the operation.
.
How to replace the number plate bulb on your Ford Edge without outside access
Second part of our content page, replace this license plate bulb on your Ford Edge without external access. Most often you will be able to access it, however some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Ford Edge
To change the one on the front plate, nothing could be easier, you will have to put yourself under the car (ideally positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, almost always kept by two soft plastic tabs by pressing on both simultaneously, then right after you have your license plate bulb block in hand, Take out the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take extra care not to exert too much pressure otherwise you will break the plastic cover), and you will just have to remove the burnt-out license plate bulb and replace it with the new , then verify and reassemble the whole thing.
How to change the rear license plate bulb on my Ford Edge
Finally last solution, you must change the bulb on the backplate of your Ford Edge, but you are not able to open the cover from the outside of your car. In this case, here is the method to do this task:
- Unplug the battery from your Ford Edge
- Find the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever carefully on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, disconnect the holders for easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Ford Edge, test it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have found out the main ways for replacing license plate bulbs on your car, be aware that on some models the technique may be a bit different but you should be able to realize it following the explanation of this content. If you can’t do it, don’t be reluctant to go to your garage area it would be a shame to break a part of your Ford Edge. If you need to change other bulbs like the position light bulbs on your Ford Edge or the low beam bulbs on Ford Edge, don’t be reluctant to consult our content articles which describe you the process to follow.
Whenever you have any additional questions about the Ford Edge, do not hesitate to consult our Ford Edge category.
