It doesn’t matter if it’s for your own personal security, for roadworthiness tests or to avoid a fine, ensuring that your headlamp bulbs are always functioning is very important. In fact, bulbs are wearing units that will predictably burn out after some time and therefore need to be replaced. You’re quite likely on this site because one of your parking lights is burnt out and you’re wondering how to change your Chevrolet Cobalt’s license plate bulb, we’ve created this article content to help you do it all on your own and not have to go to your auto mechanic. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Chevrolet Cobalt.
How to change the license plate bulb on your Chevrolet Cobalt coming from the outside
This tactic is the least difficult of the two, in truth, for this one you will just require to remove the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the case we will spend a moment on in the second section of this article content to show you the way.
So let’s begin with swapping the number plate bulb by going through the outside of your Chevrolet Cobalt. It doesn’t matter if it’s the front or the back of your car the operation will be identical.
Here are a few simple steps to follow to perform this service:
- With the engine off, unplug the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to insert the flat part into the notch provided for this purpose (generally on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Chevrolet Cobalt
- Use your screwdriver or knife to remove the bulb from its spot, in the event you are afraid of breaking a thing, you can as well do it with your fingers.
- Finally, put the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and check the light to confirm the successfulness of the task.
.
How to change the number plate bulb on your Chevrolet Cobalt without outside access
Second section of our content page, replace this license plate bulb on your Chevrolet Cobalt without external access. Generally you will be able to access it, however some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Chevrolet Cobalt
To change the one on the front plate, nothing could be much easier, you will have to put yourself under the car (ideally positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, generally held by two soft plastic tabs by pressing on both simultaneously, then once you have your license plate bulb block in hand, Take off the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take care not to apply too much pressure otherwise you will break the plastic cover), and you will only have to remove the burnt-out license plate bulb and swap it with the new , then test out and reassemble the whole thing.
How to change the rear license plate bulb on my Chevrolet Cobalt
Finally last solution, you must change the bulb on the backplate of your Chevrolet Cobalt, but you cannot open the cover from the outside of your car. In this case, here is the approach to execute this task:
- Unplug the battery from your Chevrolet Cobalt
- Identify the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever carefully on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, unplug the holders for less difficult access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Chevrolet Cobalt, check it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have learned the main methods for swapping license plate bulbs on your car, remember that on some models the methodology may be a bit different but you should be able to realize it following the outline of this document. If you can’t do it, don’t be reluctant to go to your garage area it would be a shame to break a part of your Chevrolet Cobalt. If you wish to change other bulbs like the position light bulbs on your Chevrolet Cobalt or the low beam bulbs on Chevrolet Cobalt, don’t be reluctant to read our articles which describe you the process to follow.
If you wish more tutorials on the Chevrolet Cobalt, go to our Chevrolet Cobalt category.
