Whether it’s for your personal safety, for roadworthiness testing or to avoid a fine, ensuring your headlamp bulbs are in every case effective is necessary. In reality, bulbs are wearing auto parts that will obviously burn out with time and consequently need to be replaced. You’re most likely in this article because one of your parking lights is burnt out and you’re wanting to know how to change your Porsche 911’s license plate bulb, we’ve made this article to help you do it on your own and not have to go to your auto mechanic. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Porsche 911.
How to swap the license plate bulb on your Porsche 911 through the outside
This process is the fastest of the two, in truth, for this one you will just need to take away the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the case we will dedicate a moment on in the second part of this document to show you the way.
So let’s start with replacing the number plate bulb by going through the outside of your Porsche 911. Whether it’s the front or the back of your vehicle the technique will be similar.
Here are a few simple actions to follow to carry out this routine service:
- With the engine turned off, disconnect the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to insert the flat part into the notch assigned for this intent (usually on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Porsche 911
- Use your screwdriver or knife to remove the bulb from its place, if you are worried of damaging anything, you can also do it with your fingers.
- Finally, put the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and check the light to validate the achievement of the procedure.
.
How to replace the number plate bulb on your Porsche 911 without outside access
Second part of our item, replace this license plate bulb on your Porsche 911 without external access. In most cases you will be able to access it, however some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my Porsche 911
To swap the one on the front plate, nothing could be less difficult, you will have to put yourself under the vehicle (ideally positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, usually held by two soft plastic tabs by pressing on both simultaneously, then now that you have your license plate bulb block in hand, Take out the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be cautious not to apply too much pressure otherwise you will break the plastic cover), and you will just have to take away the burnt-out license plate bulb and change it with the new , then test out and reassemble the whole thing.
How to swap the rear license plate bulb on my Porsche 911
Finally last option, you must swap the bulb on the backplate of your Porsche 911, but you simply cannot open the cover from the outside of your vehicle. In such a case, here is the technique to conduct this operation:
- Disconnect the battery from your Porsche 911
- Identify the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever gently on all the frame of the trunk to remove it.
- Once located, before removing the bulb holders, disconnect the holders for easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Porsche 911, check it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have learned the main tactics for replacing license plate bulbs on your car, take note that on some models the method may be a bit different but you should be able to accomplish it following the explanation of this article content. If you can’t do it, don’t hesitate to go to your workshop it would be a shame to break a part of your Porsche 911. If you desire to change other bulbs like the position light bulbs on your Porsche 911 or the low beam bulbs on Porsche 911, don’t hesitate to consult our articles which describe you the operation to follow.
Whenever you have any further questions about the Porsche 911, do not hesitate to consult our Porsche 911 category.
