Whether it’s for your own safety, for roadworthiness testing or to avoid a fine, ensuring your headlamp bulbs are in every case effective is fundamental. Indeed, bulbs are wearing parts that will inevitably burn out over the years and as a result need to be swapped out. You’re likely in this article because one of your parking lights is burnt out and you’re wondering how to change your Buick Regal’s license plate bulb, we’ve created this article content to help you do it all on your own and not have to go to your motor mechanic. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Buick Regal.

change-license-plate-bulb-buick-regal

How to replace the license plate bulb on your Buick Regal throughout the outside

This option is the quickest of the two, in reality, for this one you will simply require to take out the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the situation we will dedicate a moment on in the second section of this content to clarify the method.
So let’s begin with replacing the number plate bulb by going through the outside of your Buick Regal. Whether it’s the front or the back of your vehicle the method will be similar.
Here are a few simple guidelines to stick to to perform this routine service:

  • With the engine turned off, disconnect the battery terminals from your car
  • Position yourself in front of your license plate and use a flat screwdriver or knife to insert the flat part into the notch assigned for this purpose (usually on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Buick Regal
  • .

  • Use your screwdriver or knife to remove the bulb from its place, in the event you are worried of damaging something, you can also do it with your fingers.
  • Finally, position the new license plate light bulb
  • Last stage, before reassembling, reconnect your battery and test the light to confirm the success of the operation.

How to replace the number plate bulb on your Buick Regal without outside access

Second section of our content page, swap this license plate bulb on your Buick Regal without external access. In most cases you will be able to access it, however some series (often at the rear does not allow this access).

How to replace the front license plate bulb on my Buick Regal

To replace the one on the front plate, nothing could be much easier, you will have to position yourself under the vehicle (preferably put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, usually kept by two soft plastic tabs by pressing on both at the same time, then once you have your license plate bulb block in hand, Take away the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be mindful not to apply too much pressure otherwise you will break the plastic cover), and you will simply have to take out the burnt-out license plate bulb and replace it with the new , then test out and reassemble the whole thing.

How to replace the rear license plate bulb on my Buick Regal

Finally last possibility, you must replace the bulb on the backplate of your Buick Regal, but you cannot really open the cover from the outside of your vehicle. In this case, here is the process to do this task:

  • Unplug the battery from your Buick Regal
  • Locate the position of your light bulbs from the outside.
  • From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever delicately on all the frame of the trunk to remove it.
  • Once found, before removing the bulb holders, disconnect the holders for less difficult access.
  • Using a screwdriver, lever the two plastic parts to remove the bulb holder
  • .

  • Replace the burnt-out license plate bulb on your Buick Regal, test it and reassemble it, paying attention to the clips on the trunk liner

.
There you have it, you have learned the main approaches for replacing license plate bulbs on your car, take note that on some models the method may be a bit different but you should be able to do it following the outline of this content. If you can’t do it, don’t be reluctant to go to your garage it would be a shame to break a part of your Buick Regal. If you want to change other bulbs like the position light bulbs on your Buick Regal or the low beam bulbs on Buick Regal, don’t be reluctant to consult our content articles which demonstrate you the operation to follow.

If you have any further questions about the Buick Regal, do not hesitate to consult our Buick Regal category.