Regardless whether it’s for your personal security, for roadworthiness testing or to avoid a fine, being sure your headlamp bulbs are all the time working is really important. In reality, bulbs are wearing auto parts that will undoubtedly burn out in the future and as a consequence need to be replaced. You’re perhaps on this website because one of your parking lights is burnt out and you’re wondering how to change your hyundai i10’s license plate bulb, we’ve written this content page to help you do it on your own and not have to go to your mechanic. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your hyundai i10.
How to replace the license plate bulb on your hyundai i10 throughout the outside
This solution is the simplest of the two, in fact, for this one you will just need to remove the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the case we will spend a moment on in the second section of this content to explain the approach.
So let’s begin with changing the number plate bulb by going through the outside of your hyundai i10. Regardless whether it’s the front or the back of your automobile the procedure will be identical.
Here are a few simple actions to stick to to conduct this routine service:
- With the engine off, disconnect the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to insert the flat part into the notch supplied for this purpose (usually on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your hyundai i10
- Use your screwdriver or knife to eject the bulb from its location, in the event that you are scared of destroying a thing, you can also do it with your fingers.
- Finally, put the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and check the light to validate the success of the process.
.
How to replace the number plate bulb on your hyundai i10 without outside access
Second section of our document, swap this license plate bulb on your hyundai i10 without external access. Generally you will be able to access it, however some series (often at the rear does not allow this access).
How to replace the front license plate bulb on my hyundai i10
To replace the one on the front plate, nothing could be less hard, you will have to put yourself under the automobile (preferably positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, usually held by two soft plastic tabs by pressing on both at once, then once you have your license plate bulb block in hand, Take away the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be attentive not to put in too much force or you will break the plastic cover), and you will just have to remove the burnt-out license plate bulb and change it with the new , then check and reassemble the whole thing.
How to replace the rear license plate bulb on my hyundai i10
Finally last possibility, you must replace the bulb on the backplate of your hyundai i10, but you simply cannot open the cover from the outside of your automobile. In such a case, here is the process to execute this operation:
- Disconnect the battery from your hyundai i10
- Find the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever softly on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, disconnect the holders for easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your hyundai i10, check it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have found out the main approaches for changing license plate bulbs on your car, remember that on some models the technique may be a bit different but you should be able to accomplish it following the outline of this content. If you can’t do it, don’t be reluctant to go to your workshop it would be a shame to break a part of your hyundai i10. If you desire to change other bulbs like the position light bulbs on your hyundai i10 or the low beam bulbs on hyundai i10, don’t be reluctant to browse our content articles which explain you the operation to follow.
If perhaps you have any further questions about the hyundai i10, do not hesitate to consult our hyundai i10 category.
