It doesn’t matter if it’s for your specific security, for roadworthiness testing or to avoid a fine, being sure your headlamp bulbs are in every case effective is fundamental. Indeed, bulbs are wearing auto parts that will predictably burn out after a while and consequently need to be swapped out. You’re perhaps on the website because one of your parking lights is burnt out and you’re wondering how to change your Ds Ds 3’s license plate bulb, we’ve written this article content to help you do it on your own and not have to go to your technician. Firstly, we will take a look at changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Ds Ds 3.
How to change the license plate bulb on your Ds Ds 3 coming from the outside
This technique is the least difficult of the two, in truth, for this one you will only have to remove the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the case we will spend a moment on in the second part of this document to teach you the way.
So let’s begin with replacing the number plate bulb by going through the outside of your Ds Ds 3. It doesn’t matter if it’s the front or the back of your automobile the operation will be similar.
Here are a few simple actions to follow to conduct this maintenance:
- With the engine off, disconnect the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to place the flat part into the notch specified for this goal (in general on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Ds Ds 3
- Use your screwdriver or knife to remove the bulb from its location, in the event you are worried of destroying something, you can as well do it with your fingers.
- Finally, put the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and check the light to confirm the success of the process.
.
How to replace the number plate bulb on your Ds Ds 3 without outside access
Second part of our content page, replace this license plate bulb on your Ds Ds 3 without external access. Generally you will be able to access it, however some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Ds Ds 3
To change the one on the front plate, nothing could be much easier, you will have to put yourself under the automobile (ideally positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in general held by two soft plastic tabs by pressing on both simultaneously, then right after you have your license plate bulb block in hand, Take away the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be cautious not to exert too much pressure otherwise you will break the plastic cover), and you will just have to remove the burnt-out license plate bulb and change it with the new , then test out and reassemble the whole thing.
How to change the rear license plate bulb on my Ds Ds 3
Finally last option, you must change the bulb on the backplate of your Ds Ds 3, but you cannot really open the cover from the outside of your automobile. In this case, here is the technique to perform this task:
- Unplug the battery from your Ds Ds 3
- Find the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever gently on all the frame of the trunk to remove it.
- Once located, before removing the bulb holders, disconnect the holders for less complicated access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Ds Ds 3, check it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have found out the main solutions for replacing license plate bulbs on your car, be aware that on some models the methodology may be a bit different but you should be able to realize it following the explanation of this document. If you can’t do it, don’t be reluctant to go to your mechanic it would be a shame to break a part of your Ds Ds 3. If you want to change other bulbs like the position light bulbs on your Ds Ds 3 or the low beam bulbs on Ds Ds 3, don’t be reluctant to read our content articles which demonstrate you the procedure to follow.
If you wish more tutorials on the Ds Ds 3, go to our Ds Ds 3 category.
