It doesn’t matter if it’s for your specific security, for roadworthiness tests or to avoid a fine, making sure your headlamp bulbs are always working is fundamental. In fact, bulbs are wearing parts that will obviously burn out in the future and as a result need to be replaced. You’re perhaps here because one of your parking lights is burnt out and you’re worried about how to change your Chevrolet Captiva’s license plate bulb, we’ve written and published this content to help you do it without any help and not have to go to your technician. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Chevrolet Captiva.
How to swap the license plate bulb on your Chevrolet Captiva coming from the outside
This option is the fastest of the two, in reality, for this one you will just have to take out the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the situation we will dedicate some time on in the second section of this article to teach you the way.
So let’s start with swapping the number plate bulb by going through the outside of your Chevrolet Captiva. It doesn’t matter if it’s the front or the back of your car the process will be identical.
Here are a few simple actions to follow to execute this maintenance tasks:
- With the engine off, disconnect the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to insert the flat part into the notch provided for this intent (in general on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Chevrolet Captiva
- Use your screwdriver or knife to remove the bulb from its location, if you are afraid of damaging anything, you can as well do it with your fingers.
- Finally, put the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and verify the light to confirm the successfulness of the process.
.
How to replace the number plate bulb on your Chevrolet Captiva without outside access
Second section of our content, change this license plate bulb on your Chevrolet Captiva without external access. Generally you will be able to access it, however some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my Chevrolet Captiva
To swap the one on the front plate, nothing could be less difficult, you will have to put yourself under the car (ideally positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in general kept by two soft plastic tabs by pressing on both at the same time, then now that you have your license plate bulb block in hand, Take away the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take care not to exert too much force or you will break the plastic cover), and you will only have to take out the burnt-out license plate bulb and change it with the new , then check and reassemble the whole thing.
How to swap the rear license plate bulb on my Chevrolet Captiva
Finally last possibility, you must swap the bulb on the backplate of your Chevrolet Captiva, but you cannot open the cover from the outside of your car. In this instance, here is the approach to accomplish this task:
- Disconnect the battery from your Chevrolet Captiva
- Find the spot of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever carefully on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, disconnect the holders for easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Chevrolet Captiva, verify it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have found out the main approaches for swapping license plate bulbs on your car, be aware that on some models the technique may be a bit different but you should be able to realize it following the explanation of this article content. If you can’t do it, don’t hesitate to go to your garage it would be a shame to break a part of your Chevrolet Captiva. If you desire to change other bulbs like the position light bulbs on your Chevrolet Captiva or the low beam bulbs on Chevrolet Captiva, don’t hesitate to read our content articles which explain you the procedure to follow.
Whenever you have any further questions about the Chevrolet Captiva, do not hesitate to consult our Chevrolet Captiva category.
