It doesn’t matter if it’s for your specific security, for roadworthiness tests or to avoid a fine, making sure your headlamp bulbs are constantly working is very important. Indeed, bulbs are wearing auto parts that will undoubtedly burn out after awhile and consequently need to be swapped out. You’re most certainly on this website because one of your parking lights is burnt out and you’re worried about how to change your Audi A1’s license plate bulb, we’ve created this article content to help you do it by yourself and not have to go to your motor mechanic. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Audi A1.

change-license-plate-bulb-audi-a1

How to swap the license plate bulb on your Audi A1 through the outside

This tactic is the most simple of the two, in reality, for this one you will just have to remove the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the situation we will spend some time on in the second section of this content to explain the method.
So let’s begin with changing the number plate bulb by going through the outside of your Audi A1. It doesn’t matter if it’s the front or the back of your vehicle the procedure will be similar.
Here are a few simple actions to follow to carry out this maintenance tasks:

  • With the engine off, disconnect the battery terminals from your car
  • Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch assigned for this purpose (in most cases on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Audi A1
  • .

  • Use your screwdriver or knife to eject the bulb from its place, if you are worried of destroying a thing, you can also do it with your fingers.
  • Finally, put the new license plate light bulb
  • Last step, before reassembling, reconnect your battery and verify the light to confirm the successfulness of the operation.

How to replace the number plate bulb on your Audi A1 without outside access

Second section of our content page, swap this license plate bulb on your Audi A1 without external access. Most often you will be able to access it, nevertheless some series (often at the rear does not allow this access).

How to swap the front license plate bulb on my Audi A1

To swap the one on the front plate, nothing could be less complicated, you will have to put yourself under the vehicle (ideally placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in most cases kept by two soft plastic tabs by pressing on both simultaneously, then right after you have your license plate bulb block in hand, Take away the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take extra care not to apply too much force or you will break the plastic cover), and you will only have to remove the burnt-out license plate bulb and replace it with the new , then verify and reassemble the whole thing.

How to swap the rear license plate bulb on my Audi A1

Finally last possibility, you must swap the bulb on the backplate of your Audi A1, but you simply cannot open the cover from the outside of your vehicle. In this case, here is the solution to carry out this operation:

  • Unplug the battery from your Audi A1
  • Identify the location of your light bulbs from the outside.
  • From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever gently on all the frame of the trunk to remove it.
  • Once located, before removing the bulb holders, disconnect the holders for much easier access.
  • Using a screwdriver, lever the two plastic parts to remove the bulb holder
  • .

  • Replace the burnt-out license plate bulb on your Audi A1, verify it and reassemble it, paying attention to the clips on the trunk liner

.
There you have it, you have discovered the main solutions for changing license plate bulbs on your car, remember that on some models the method may be a bit different but you should be able to accomplish it following the explanation of this article content. If you can’t do it, don’t be reluctant to go to your garage it would be a shame to break a part of your Audi A1. If you desire to change other bulbs like the position light bulbs on your Audi A1 or the low beam bulbs on Audi A1, don’t be reluctant to read our content articles which describe you the process to follow.

To discover more tips on the Audi A1, take a look at the Audi A1 category.