If you experience you can’t see as well at night, or you experience you’re lighting too low, or too high, in all these circumstances, there’s only one component of your vehicle responsible – your headlights, as well known as high beams. Although this adjustment may appear easy thanks to the thumbwheel on your dashboard, a complete adjustment is much more technical than this elementary manipulation, and in this article, we are going to discover how to adjust the headlights of your Dodge Ram? To do this, first we will discover why you need to adjust your high beams, and secondly how to adjust the headlights of your Dodge Ram.
Why adjust the headlights of your Dodge Ram?
So let’s start our content page with the benefit of adjusting the headlights of your Dodge Ram. For many of us, our headlights are adjusted sufficiently, and they appear to light up enough after dark. Unfortunately this is not always the case and checking this setting, either because the headlights on your Dodge Ram are not bright enough, or because you have the feeling that they are too weak is a wise decision .
Adjusting the high beams of your Dodge Ram for safety
To begin with, the headlight adjustment of a Dodge Ram must be carried out for a simple security reason. If it’s for you, or for the other users you come across during your night trips. In fact, if you don’t see enough, the risk is to miss an obstacle while traveling, or to predict a curve badly. On the other hand, if your headlights are too powerful, even if you are supposed to switch to low beam lights when you pass a vehicle, the time required to make this switch will most of the time expose the driver in front of you to the headlight beam of your Dodge Ram . It is therefore important for others as well as for you to have an optimal adjustment of your headlights.
Adjusting the headlights of a Dodge Ram for legal reasons
Furthermore to security, there is a law that regulates the power, the adjustment of motor vehicle headlights (articles R313-2 of the Highway Code), here is what it suggests: have between 2 and 4 headlights that illuminate at minimum 100 meters. Another legislation regulates their use, the European one (directive 76/756/EEC), which stipulates that there is no maximum height for the adjustment of the headlights, but that the maximum width of the beam must be very same to that of the dipped headlights and that the maximum luminosity must be 225, 000 cd.
How to adjust the headlights of a Dodge Ram?
We will now proceed to the section that concerns you the most in this article, how to adjust the headlights of his Dodge Ram? This setting may appear a bit complicated, but by following the instructions you should have the ability to complete it without too much concern.
Preparations to adjust the headlights of a Dodge Ram
To begin with, you’ll need to prepare your vehicle to adjust your high beams in good conditions, here are the preparations to put in place:
- Place your vehicle on a surface in front of a white wall for example, about 4 or 5 meters from the wall.
- Check your tire pressure attentively.
- Check that the height adjustment knob for the lights is set to 0
- Try doing that with half a full tank.
- Remove all needless weight from the automobile, only one person should be in the driver’s seat.
.
The headlight adjustment of his Dodge Ram
Once your car is in position, you will turn on your dipped beam and make a cross-shaped mark (one horizontal and one vertical section) in the middle of the beam that will be projected on the wall. Check with a level that both parts of the cross are straight. Then back your vehicle up to a distance of between 7 and 10 metres. For the rest of the process here are the steps to follow:
- Open your hood, locate the screws for horizontal and vertical adjustment of the headlights of your Dodge Ram (they are usually designated, and those on top must adjust the verticality and the one on the side controls the horizontality of the adjustment).
- Use a cloth or something else to hide the projector on which you are not making the correction.
- Using the screws to make the horizontal correction, you should have the most intense component of the beam which should be a little to the right of the vertical line marked on the wall
- With regard to vertical correction, you will have to use the screw to try to position the upper end of the beam at the level of the horizontal marking on the wall, or slightly down below.
- Once finished, verify that the headlights setting of your Dodge Ram is coherent, do not think twice to verify it after you have driven it, sometimes it may move.
.
.
If you want to adjust the fog lights on your Dodge Ram, please go through our content page on this subject matter.
To discover more tips on the Dodge Ram, take a look at the Dodge Ram category.
