It doesn’t matter if it’s for your own security, for roadworthiness testing or to avoid a fine, being sure your headlamp bulbs are always effective is fundamental. In reality, bulbs are wearing units that will obviously burn out after some time and as a result need to be replaced. You’re almost certainly on this website because one of your parking lights is burnt out and you’re worried about how to change your Dodge Ram’s license plate bulb, we’ve written and published this article to help you do it without any help and not have to go to your motor mechanic. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Dodge Ram.
How to swap the license plate bulb on your Dodge Ram throughout the outside
This solution is the least difficult of the two, actually, for this one you will simply require to take away the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the situation we will spend some time on in the second section of this article content to clarify the approach.
So let’s start with changing the number plate bulb by going through the outside of your Dodge Ram. It doesn’t matter if it’s the front or the back of your automobile the procedure will be the same.
Here are a few simple steps to stick to to conduct this maintenance:
- With the engine off, unplug the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to insert the flat part into the notch provided for this goal (in most cases on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Dodge Ram
- Use your screwdriver or knife to eject the bulb from its spot, in the event you are afraid of damaging anything, you can as well do it with your fingers.
- Finally, put the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and test the light to validate the success of the operation.
.
How to replace the number plate bulb on your Dodge Ram without outside access
Second section of our article, change this license plate bulb on your Dodge Ram without external access. Most often you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my Dodge Ram
To swap the one on the front plate, nothing could be less complicated, you will have to put yourself under the automobile (preferably placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in most cases kept by two soft plastic tabs by pressing on both at once, then right after you have your license plate bulb block in hand, Take off the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be cautious not to exert too much force otherwise you will break the plastic cover), and you will just have to take away the burnt-out license plate bulb and change it with the new , then test out and reassemble the whole thing.
How to swap the rear license plate bulb on my Dodge Ram
Finally last option, you must swap the bulb on the backplate of your Dodge Ram, but you are not able to open the cover from the outside of your automobile. In this case, here is the method to do this task:
- Disconnect the battery from your Dodge Ram
- Find the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever gently on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, unplug the holders for easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Dodge Ram, test it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have found out the main solutions for changing license plate bulbs on your car, be aware that on some models the method may be a bit different but you should be able to accomplish it following the outline of this content page. If you can’t do it, don’t hesitate to go to your workshop it would be a shame to break a part of your Dodge Ram. If you need to change other bulbs like the position light bulbs on your Dodge Ram or the low beam bulbs on Dodge Ram, don’t hesitate to consult our content articles which describe you the process to follow.
If perhaps you have any additional questions about the Dodge Ram, do not hesitate to consult our Dodge Ram category.
