If you’re a bit of a do-it-yourselfer, you’re most likely eager to manage most of the service to be achieved on your Acura TL, but some are more challenging than others and require the removal of body parts or elements to access the part you want to focus on. We really want to help you in this operation. That’s why on this web page we are going to discover how to remove the bumper from a Acura TL. This task is not very challenging and you should be able to do it with few tools. For that, first we will see how to remove the front bumper of your Acura TL, then how to remove the rear bumper of this one.
How to remove the front bumper from a Acura TL
So let’s commence our content with the front bumper of your Acura TL. To remove it, you will just need a set of ratchet wrenches, some screwdrivers and torx bits. Here are the guidelines you will have to stick to in order to disassemble the bumper of your Acura TL in good conditions:
- If you want to be more comfy, we encourage you to put your Acura TL on stands and to remove the front wheels to have a best access to the whole front bumper.
- Open the bonnet of your motor vehicle: Would seem obvious, but you will need to have access to the bumper attachment in your engine compartment.
- Take out the wheel arches: They’re also referred to as fenders, but they’ll get in the way and prevent you from accessing all the screws on the front bumper of your Acura TL. According to your automobile features and the year of your model, you will also have the ability to find staples, to get this done, you will just have to use a staple extractor or to do it delicately with a big flat screwdriver, and use a lever to open the staple.
- Then you will have to unscrew the screws that is behind your mudguard and that seals the front bumper of your Acura TL on the sides.
- Unscrew the screws or remove the clips on the upper part of the bumper in the engine bay.
- Now it’s time to go below your Acura TL to unscrew the bolts that are on the chassis of the automobile, you will find some in the middle of the bumper and on the sides.
- Make sure unplug the connection of the plate lighting and the distance control sensor if you have it.
- Carefully remove the front bumper by first unclipping the sides. If it doesn’t come off, you probably forgot a screw or a clip. Think of using a carpet or other to prevent that it gets scratched by touching the ground.
That’s it, you’ve seen all the steps of how to remove the front bumper from your Acura TL, to put it back in place stick to the steps in the opposite way.
How to remove the rear bumper from a Acura TL
And to finish, regardless if the process is quite similar, we will take a look at the case of removing the rear bumper from your Acura TL. For each stage to avoid repeating ourselves we will exclusively give you the broad outlines, refer to part 1 if you have any uncertainties or questions for more details.
- Start by undertaking the same first stage, that is, lift your Acura TL and remove your rear wheels in order to have an ideal working space to remove the bumper of your Acura TL without trouble
- Remove the rear wheel arches of your Acura TL to access the side bumper side brackets
- Open your trunk
- Take out the side brackets in your wheel arches to make it less difficult to remove the bumper from your Acura TL.
- Take away the lower bindings below your Acura TL.
- While doing so, make sure to un plug the rear license plate light and the reverse radar sensors if you are equipped with them.
- Unscrew the top brackets from the top of the trunk.
- Now all you have to do is remove the rear bumper from your Acura TL, stick to the same process as for the front bumper
Here, you have learned through these two parts, how to remove the bumper from a Acura TL whether it is the front one or the rear one the methods are pretty much the same and it is enough to be meticulous to make everything go well.
To get more tips on the Acura TL, take a look at the Acura TL category.
