It doesn’t matter if it’s for your personal safety, for roadworthiness testing or to avoid a fine, being sure your headlamp bulbs are constantly functional is extremely important. In fact, bulbs are wearing units that will undoubtedly burn out as time passes and as a result need to be replaced. You’re probably in this article because one of your parking lights is burnt out and you’re wanting to know how to change your Toyota Land Cruiser Serie 70’s license plate bulb, we’ve made this content page to help you do it all on your own and not have to go to your motor mechanic. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Toyota Land Cruiser Serie 70.
How to change the license plate bulb on your Toyota Land Cruiser Serie 70 coming from the outside
This process is the fastest of the two, in truth, for this one you will only have to remove the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the situation we will dedicate some time on in the second part of this content page to teach you the method.
So let’s begin with replacing the number plate bulb by going through the outside of your Toyota Land Cruiser Serie 70. It doesn’t matter if it’s the front or the back of your vehicle the operation will be identical.
Here are a few simple actions to follow to carry out this routine service:
- With the engine off, disconnect the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to insert the flat part into the notch specified for this goal (almost always on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Toyota Land Cruiser Serie 70
- Use your screwdriver or knife to remove the bulb from its place, in the event that you are worried of destroying a thing, you can as well do it with your fingers.
- Finally, position the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and check the light to validate the achievement of the process.
.
How to change the number plate bulb on your Toyota Land Cruiser Serie 70 without outside access
Second part of our content page, replace this license plate bulb on your Toyota Land Cruiser Serie 70 without external access. In most cases you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Toyota Land Cruiser Serie 70
To change the one on the front plate, nothing could be much easier, you will have to position yourself under the vehicle (ideally placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, almost always kept by two soft plastic tabs by pressing on both simultaneously, then right after you have your license plate bulb block in hand, Take off the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take care not to put in too much pressure or you will break the plastic cover), and you will just have to remove the burnt-out license plate bulb and swap it with the new , then test and reassemble the whole thing.
How to change the rear license plate bulb on my Toyota Land Cruiser Serie 70
Finally last solution, you must change the bulb on the backplate of your Toyota Land Cruiser Serie 70, but you are not able to open the cover from the outside of your vehicle. In this instance, here is the process to conduct this operation:
- Disconnect the battery from your Toyota Land Cruiser Serie 70
- Identify the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever softly on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, disconnect the holders for less complicated access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Toyota Land Cruiser Serie 70, check it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have discovered the main techniques for replacing license plate bulbs on your car, take notice that on some models the method may be a bit different but you should be able to accomplish it following the outline of this document. If you can’t do it, don’t be reluctant to go to your garage it would be a shame to break a part of your Toyota Land Cruiser Serie 70. If you need to change other bulbs like the position light bulbs on your Toyota Land Cruiser Serie 70 or the low beam bulbs on Toyota Land Cruiser Serie 70, don’t be reluctant to read our articles which describe you the operation to follow.
If you have any additional questions about the Toyota Land Cruiser Serie 70, do not hesitate to consult our Toyota Land Cruiser Serie 70 category.
