Regardless whether it’s for your specific security, for roadworthiness testing or to avoid a fine, ensuring that your headlamp bulbs are all the time functioning is necessary. In reality, bulbs are wearing units that will inevitably burn out over time and as a consequence need to be changed. You’re perhaps here because one of your parking lights is burnt out and you’re wondering how to change your Tesla Model S’s license plate bulb, we’ve created this article content to help you do it all on your own and not have to go to your auto technician. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Tesla Model S.
How to swap the license plate bulb on your Tesla Model S through the outside
This option is the simplest of the two, in fact, for this one you will just need to take out the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the case we will dedicate a moment on in the second part of this content to clarify the approach.
So let’s start with replacing the number plate bulb by going through the outside of your Tesla Model S. Regardless whether it’s the front or the back of your vehicle the procedure will be similar.
Here are a few simple steps to stick to to execute this maintenance:
- With the engine off, disconnect the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch assigned for this purpose (in most cases on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Tesla Model S
- Use your screwdriver or knife to remove the bulb from its spot, in the event you are scared of destroying anything, you can as well do it with your fingers.
- Finally, position the new license plate light bulb
- Last step, before reassembling, reconnect your battery and check the light to confirm the success of the task.
.
How to change the number plate bulb on your Tesla Model S without outside access
Second part of our item, replace this license plate bulb on your Tesla Model S without external access. Generally you will be able to access it, however some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my Tesla Model S
To swap the one on the front plate, nothing could be less complicated, you will have to position yourself under the vehicle (ideally put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in most cases kept by two soft plastic tabs by pressing on both at the same time, then now that you have your license plate bulb block in hand, Take out the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be cautious not to apply too much pressure otherwise you will break the plastic cover), and you will only have to take out the burnt-out license plate bulb and change it with the new , then verify and reassemble the whole thing.
How to swap the rear license plate bulb on my Tesla Model S
Finally last solution, you must swap the bulb on the backplate of your Tesla Model S, but you cannot open the cover from the outside of your vehicle. In this case, here is the method to carry out this task:
- Disconnect the battery from your Tesla Model S
- Identify the spot of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever carefully on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, disconnect the holders for much easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Tesla Model S, check it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have discovered the main methods for replacing license plate bulbs on your car, remember that on some models the method may be a bit different but you should be able to realize it following the outline of this content page. If you can’t do it, don’t hesitate to go to your garage it would be a shame to break a part of your Tesla Model S. If you desire to change other bulbs like the position light bulbs on your Tesla Model S or the low beam bulbs on Tesla Model S, don’t hesitate to read our articles which describe you the procedure to follow.
In the event that you have any additional questions about the Tesla Model S, do not hesitate to consult our Tesla Model S category.
