Regardless it’s for your specific safety, for roadworthiness testing or to avoid a fine, ensuring that your headlamp bulbs are in every case operational is extremely important. In fact, bulbs are wearing units that will surely burn out in the future and as a result need to be replaced. You’re perhaps on this site because one of your parking lights is burnt out and you’re wondering how to change your Toyota Land Cruiser Serie 120’s license plate bulb, we’ve written and published this article content to help you do it all on your own and not have to go to your technician. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Toyota Land Cruiser Serie 120.
How to replace the license plate bulb on your Toyota Land Cruiser Serie 120 throughout the outside
This process is the most simple of the two, in reality, for this one you will only require to take out the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the case we will take a moment on in the second section of this content to demonstrate the method.
So let’s begin with replacing the number plate bulb by going through the outside of your Toyota Land Cruiser Serie 120. Regardless it’s the front or the back of your automobile the procedure will be the same.
Here are a few simple guidelines to stick to to perform this service:
- With the engine off, unplug the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch supplied for this purpose (in general on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Toyota Land Cruiser Serie 120
- Use your screwdriver or knife to eject the bulb from its spot, in the event you are scared of destroying something, you can also do it with your fingers.
- Finally, position the new license plate light bulb
- Last step, before reassembling, reconnect your battery and verify the light to validate the successfulness of the task.
.
How to change the number plate bulb on your Toyota Land Cruiser Serie 120 without outside access
Second section of our document, swap this license plate bulb on your Toyota Land Cruiser Serie 120 without external access. Most often you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to replace the front license plate bulb on my Toyota Land Cruiser Serie 120
To replace the one on the front plate, nothing could be simpler, you will have to position yourself under the automobile (preferably placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in general held by two soft plastic tabs by pressing on both simultaneously, then right after you have your license plate bulb block in hand, Remove the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be mindful not to put in too much pressure otherwise you will break the plastic cover), and you will just have to take out the burnt-out license plate bulb and swap it with the new , then verify and reassemble the whole thing.
How to replace the rear license plate bulb on my Toyota Land Cruiser Serie 120
Finally last option, you must replace the bulb on the backplate of your Toyota Land Cruiser Serie 120, but you cannot open the cover from the outside of your automobile. In this instance, here is the tactic to operate this task:
- Disconnect the battery from your Toyota Land Cruiser Serie 120
- Find the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever softly on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, unplug the holders for easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Toyota Land Cruiser Serie 120, verify it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have found out the main approaches for replacing license plate bulbs on your car, bear in mind that on some models the methodology may be a bit different but you should be able to do it following the outline of this content. If you can’t do it, don’t hesitate to go to your workshop it would be a shame to break a part of your Toyota Land Cruiser Serie 120. If you need to change other bulbs like the position light bulbs on your Toyota Land Cruiser Serie 120 or the low beam bulbs on Toyota Land Cruiser Serie 120, don’t hesitate to consult our content articles which describe you the operation to follow.
If you want more guides on the Toyota Land Cruiser Serie 120, go to our Toyota Land Cruiser Serie 120 category.
