It doesn’t matter if it’s for your specific security, for roadworthiness tests or to avoid a fine, ensuring that your headlamp bulbs are all the time effective is extremely important. Indeed, bulbs are wearing parts that will obviously burn out after some time and therefore need to be swapped out. You’re almost certainly on this site because one of your parking lights is burnt out and you’re wanting to know how to change your Toyota C HR’s license plate bulb, we’ve made this content to help you do it by yourself and not have to go to your technician. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Toyota C HR.
How to replace the license plate bulb on your Toyota C HR throughout the outside
This approach is the most simple of the two, in reality, for this one you will just require to take out the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the case we will spend some time on in the second section of this document to teach you the method.
So let’s begin with changing the number plate bulb by going through the outside of your Toyota C HR. It doesn’t matter if it’s the front or the back of your motor vehicle the process will be the same.
Here are a few simple actions to stick to to carry out this routine service:
- With the engine turned off, disconnect the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to insert the flat part into the notch provided for this intent (commonly on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Toyota C HR
- Use your screwdriver or knife to eject the bulb from its placement, in the event that you are scared of damaging something, you can also do it with your fingers.
- Finally, put the new license plate light bulb
- Last step, before reassembling, reconnect your battery and check the light to validate the achievement of the process.
.
How to replace the number plate bulb on your Toyota C HR without outside access
Second section of our article, replace this license plate bulb on your Toyota C HR without external access. Most often you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to replace the front license plate bulb on my Toyota C HR
To replace the one on the front plate, nothing could be much easier, you will have to put yourself under the motor vehicle (ideally positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, commonly held by two soft plastic tabs by pressing on both at the same time, then once you have your license plate bulb block in hand, Take off the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take extra care not to put in too much force or you will break the plastic cover), and you will only have to take out the burnt-out license plate bulb and change it with the new , then check and reassemble the whole thing.
How to replace the rear license plate bulb on my Toyota C HR
Finally last solution, you must replace the bulb on the backplate of your Toyota C HR, but you simply cannot open the cover from the outside of your motor vehicle. In such a case, here is the approach to execute this operation:
- Unplug the battery from your Toyota C HR
- Find the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever gently on all the frame of the trunk to remove it.
- Once located, before removing the bulb holders, disconnect the holders for much easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Toyota C HR, check it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have found out the main solutions for changing license plate bulbs on your car, be aware that on some models the technique may be a bit different but you should be able to accomplish it following the outline of this article content. If you can’t do it, don’t be reluctant to go to your garage area it would be a shame to break a part of your Toyota C HR. If you want to change other bulbs like the position light bulbs on your Toyota C HR or the low beam bulbs on Toyota C HR, don’t be reluctant to browse our articles which explain you the process to follow.
In the event that you have any further questions about the Toyota C HR, do not hesitate to consult our Toyota C HR category.
