Regardless it’s for your own personal security, for roadworthiness tests or to avoid a fine, ensuring that your headlamp bulbs are constantly functional is extremely important. In fact, bulbs are wearing auto parts that will inevitably burn out after some time and as a result need to be replaced. You’re likely on the website because one of your parking lights is burnt out and you’re struggling with how to change your Peugeot 107’s license plate bulb, we’ve written and published this document to help you do it without any help and not have to go to your motor mechanic. Firstly, we will take a look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Peugeot 107.
How to swap the license plate bulb on your Peugeot 107 through the outside
This process is the easiest of the two, in fact, for this one you will simply require to take out the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the situation we will spend a moment on in the second part of this article content to show you the way.
So let’s begin with swapping the number plate bulb by going through the outside of your Peugeot 107. Regardless it’s the front or the back of your vehicle the procedure will be similar.
Here are a few simple steps to stick to to perform this maintenance tasks:
- With the engine turned off, disconnect the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to insert the flat part into the notch provided for this purpose (in most cases on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Peugeot 107
- Use your screwdriver or knife to remove the bulb from its location, if you are worried of damaging anything, you can as well do it with your fingers.
- Finally, put the new license plate light bulb
- Last step, before reassembling, reconnect your battery and check the light to validate the achievement of the procedure.
.
How to change the number plate bulb on your Peugeot 107 without outside access
Second part of our item, replace this license plate bulb on your Peugeot 107 without external access. Most often you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my Peugeot 107
To swap the one on the front plate, nothing could be less hard, you will have to put yourself under the vehicle (ideally positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in most cases held by two soft plastic tabs by pressing on both at once, then now that you have your license plate bulb block in hand, Take off the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take care not to put in too much force otherwise you will break the plastic cover), and you will simply have to take out the burnt-out license plate bulb and change it with the new , then test and reassemble the whole thing.
How to swap the rear license plate bulb on my Peugeot 107
Finally last possibility, you must swap the bulb on the backplate of your Peugeot 107, but you are not able to open the cover from the outside of your vehicle. In such a case, here is the process to perform this task:
- Unplug the battery from your Peugeot 107
- Find the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever gently on all the frame of the trunk to remove it.
- Once located, before removing the bulb holders, disconnect the holders for less difficult access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Peugeot 107, check it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have found out the main methods for swapping license plate bulbs on your car, be aware that on some models the technique may be a bit different but you should be able to realize it following the outline of this document. If you can’t do it, don’t hesitate to go to your garage area it would be a shame to break a part of your Peugeot 107. If you wish to change other bulbs like the position light bulbs on your Peugeot 107 or the low beam bulbs on Peugeot 107, don’t hesitate to read our articles which demonstrate you the process to follow.
To find more tips on the Peugeot 107, take a look at the Peugeot 107 category.
