Whether it’s for your own personal security, for roadworthiness tests or to avoid a fine, ensuring that your headlamp bulbs are always functioning is very important. Indeed, bulbs are wearing parts that will inevitably burn out as time passes and consequently need to be swapped out. You’re most certainly on this website because one of your parking lights is burnt out and you’re struggling with how to change your Nissan Pulsar’s license plate bulb, we’ve written this article content to help you do it by yourself and not have to go to your motor mechanic. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Nissan Pulsar.

change-license-plate-bulb-nissan-pulsar

How to swap the license plate bulb on your Nissan Pulsar coming from the outside

This technique is the most simple of the two, in truth, for this one you will just need to take out the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the situation we will spend some time on in the second part of this article content to explain the method.
So let’s start with changing the number plate bulb by going through the outside of your Nissan Pulsar. Whether it’s the front or the back of your car the process will be similar.
Here are a few simple steps to stick to to execute this routine service:

  • With the engine turned off, disconnect the battery terminals from your car
  • Face your license plate and use a flat screwdriver or knife to insert the flat part into the notch provided for this intent (generally on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Nissan Pulsar
  • .

  • Use your screwdriver or knife to remove the bulb from its placement, in the event that you are afraid of damaging anything, you can as well do it with your fingers.
  • Finally, put the new license plate light bulb
  • Last stage, before reassembling, reconnect your battery and test the light to confirm the success of the procedure.

How to replace the number plate bulb on your Nissan Pulsar without outside access

Second part of our article, swap this license plate bulb on your Nissan Pulsar without external access. Generally you will be able to access it, however some series (often at the rear does not allow this access).

How to swap the front license plate bulb on my Nissan Pulsar

To swap the one on the front plate, nothing could be less complicated, you will have to put yourself under the car (ideally positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, generally kept by two soft plastic tabs by pressing on both at once, then right after you have your license plate bulb block in hand, Take out the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be careful not to exert too much pressure otherwise you will break the plastic cover), and you will only have to take out the burnt-out license plate bulb and swap it with the new , then test and reassemble the whole thing.

How to swap the rear license plate bulb on my Nissan Pulsar

Finally last option, you must swap the bulb on the backplate of your Nissan Pulsar, but you simply cannot open the cover from the outside of your car. In this case, here is the solution to execute this task:

  • Unplug the battery from your Nissan Pulsar
  • Find the spot of your light bulbs from the outside.
  • From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever gently on all the frame of the trunk to remove it.
  • Once established, before removing the bulb holders, disconnect the holders for less difficult access.
  • Using a screwdriver, lever the two plastic parts to remove the bulb holder
  • .

  • Replace the burnt-out license plate bulb on your Nissan Pulsar, test it and reassemble it, watching the clips on the trunk liner

.
There you have it, you have found out the main methods for changing license plate bulbs on your car, take note that on some models the method may be a bit different but you should be able to accomplish it following the explanation of this content page. If you can’t do it, don’t hesitate to go to your mechanic it would be a shame to break a part of your Nissan Pulsar. If you need to change other bulbs like the position light bulbs on your Nissan Pulsar or the low beam bulbs on Nissan Pulsar, don’t hesitate to consult our content articles which describe you the operation to follow.

If you have any further questions about the Nissan Pulsar, do not hesitate to consult our Nissan Pulsar category.