It doesn’t matter if it’s for your personal security, for roadworthiness testing or to avoid a fine, ensuring that your headlamp bulbs are constantly functional is extremely important. In reality, bulbs are wearing units that will undoubtedly burn out over time and consequently need to be replaced. You’re most likely on this website because one of your parking lights is burnt out and you’re wondering how to change your Mercedes Benz GLE Class’s license plate bulb, we’ve written this article content to help you do it without any help and not have to go to your auto technician. Firstly, we will take a look at changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Mercedes Benz GLE Class.
How to swap the license plate bulb on your Mercedes Benz GLE Class throughout the outside
This method is the quickest of the two, actually, for this one you will only need to take away the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the case we will dedicate some time on in the second section of this document to demonstrate the method.
So let’s start with swapping the number plate bulb by going through the outside of your Mercedes Benz GLE Class. It doesn’t matter if it’s the front or the back of your motor vehicle the operation will be the same.
Here are a few simple guidelines to stick to to execute this routine service:
- With the engine turned off, disconnect the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to insert the flat part into the notch supplied for this intent (usually on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Mercedes Benz GLE Class
- Use your screwdriver or knife to eject the bulb from its spot, in the event you are worried of destroying a thing, you can also do it with your fingers.
- Finally, put the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and test the light to confirm the achievement of the task.
.
How to replace the number plate bulb on your Mercedes Benz GLE Class without outside access
Second section of our article, replace this license plate bulb on your Mercedes Benz GLE Class without external access. In most cases you will be able to access it, but some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my Mercedes Benz GLE Class
To swap the one on the front plate, nothing could be simpler, you will have to put yourself under the motor vehicle (ideally put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, usually kept by two soft plastic tabs by pressing on both simultaneously, then now that you have your license plate bulb block in hand, Take out the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be mindful not to put in too much pressure or you will break the plastic cover), and you will only have to take away the burnt-out license plate bulb and change it with the new , then check and reassemble the whole thing.
How to swap the rear license plate bulb on my Mercedes Benz GLE Class
Finally last solution, you must swap the bulb on the backplate of your Mercedes Benz GLE Class, but you cannot really open the cover from the outside of your motor vehicle. In this case, here is the process to carry out this task:
- Disconnect the battery from your Mercedes Benz GLE Class
- Identify the spot of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever carefully on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, disconnect the holders for much easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Mercedes Benz GLE Class, test it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have discovered the main methods for swapping license plate bulbs on your car, remember that on some models the methodology may be a bit different but you should be able to do it following the explanation of this article. If you can’t do it, don’t hesitate to go to your mechanic it would be a shame to break a part of your Mercedes Benz GLE Class. If you desire to change other bulbs like the position light bulbs on your Mercedes Benz GLE Class or the low beam bulbs on Mercedes Benz GLE Class, don’t hesitate to read our articles which demonstrate you the process to follow.
If you have any additional questions about the Mercedes Benz GLE Class, do not hesitate to consult our Mercedes Benz GLE Class category.
