Whether it’s for your own personal safety, for roadworthiness testing or to avoid a fine, being sure your headlamp bulbs are constantly effective is extremely important. In fact, bulbs are wearing units that will obviously burn out in the future and consequently need to be replaced. You’re quite likely here because one of your parking lights is burnt out and you’re struggling with how to change your Chrysler Pacifica’s license plate bulb, we’ve written this content to help you do it without any help and not have to go to your auto mechanic. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Chrysler Pacifica.

change-license-plate-bulb-chrysler-pacifica

How to swap the license plate bulb on your Chrysler Pacifica through the outside

This solution is the most simple of the two, in truth, for this one you will only need to remove the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the situation we will dedicate a moment on in the second part of this content page to demonstrate the method.
So let’s begin with changing the number plate bulb by going through the outside of your Chrysler Pacifica. Whether it’s the front or the back of your car the operation will be identical.
Here are a few simple steps to stick to to conduct this maintenance:

  • With the engine off, unplug the battery terminals from your car
  • Position yourself in front of your license plate and use a flat screwdriver or knife to insert the flat part into the notch supplied for this goal (almost always on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Chrysler Pacifica
  • .

  • Use your screwdriver or knife to eject the bulb from its placement, if you are afraid of damaging anything, you can also do it with your fingers.
  • Finally, put the new license plate light bulb
  • Last step, before reassembling, reconnect your battery and test the light to validate the successfulness of the process.

How to change the number plate bulb on your Chrysler Pacifica without outside access

Second part of our item, change this license plate bulb on your Chrysler Pacifica without external access. In most cases you will be able to access it, but some series (often at the rear does not allow this access).

How to swap the front license plate bulb on my Chrysler Pacifica

To swap the one on the front plate, nothing could be less hard, you will have to put yourself under the car (preferably put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, almost always kept by two soft plastic tabs by pressing on both simultaneously, then right after you have your license plate bulb block in hand, Remove the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take extra care not to exert too much pressure otherwise you will break the plastic cover), and you will only have to remove the burnt-out license plate bulb and change it with the new , then check and reassemble the whole thing.

How to swap the rear license plate bulb on my Chrysler Pacifica

Finally last option, you must swap the bulb on the backplate of your Chrysler Pacifica, but you simply cannot open the cover from the outside of your car. In this instance, here is the tactic to perform this task:

  • Disconnect the battery from your Chrysler Pacifica
  • Identify the location of your light bulbs from the outside.
  • From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever softly on all the frame of the trunk to remove it.
  • Once located, before removing the bulb holders, unplug the holders for easier access.
  • Using a screwdriver, lever the two plastic parts to remove the bulb holder
  • .

  • Replace the burnt-out license plate bulb on your Chrysler Pacifica, test it and reassemble it, watching the clips on the trunk liner

.
There you have it, you have learned the main methods for changing license plate bulbs on your car, take note that on some models the technique may be a bit different but you should be able to accomplish it following the explanation of this content page. If you can’t do it, don’t hesitate to go to your garage it would be a shame to break a part of your Chrysler Pacifica. If you desire to change other bulbs like the position light bulbs on your Chrysler Pacifica or the low beam bulbs on Chrysler Pacifica, don’t hesitate to consult our content articles which demonstrate you the process to follow.

If you want more tutorials on the Chrysler Pacifica, go to our Chrysler Pacifica category.