Regardless it’s for your own safety, for roadworthiness testing or to avoid a fine, being certain your headlamp bulbs are always effective is fundamental. In fact, bulbs are wearing parts that will obviously burn out as time passes and consequently need to be changed. You’re most likely here because one of your parking lights is burnt out and you’re struggling with how to change your Ram ProMaster’s license plate bulb, we’ve created this article content to help you do it by yourself and not have to go to your auto mechanic. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Ram ProMaster.
How to change the license plate bulb on your Ram ProMaster coming from the outside
This method is the least difficult of the two, in truth, for this one you will only need to take off the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the situation we will dedicate a moment on in the second section of this article to explain the way.
So let’s start with changing the number plate bulb by going through the outside of your Ram ProMaster. Regardless it’s the front or the back of your motor vehicle the process will be similar.
Here are a few simple guidelines to follow to carry out this maintenance:
- With the engine turned off, unplug the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to place the flat part into the notch assigned for this goal (in general on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Ram ProMaster
- Use your screwdriver or knife to remove the bulb from its placement, in the event you are worried of damaging anything, you can as well do it with your fingers.
- Finally, position the new license plate light bulb
- Last step, before reassembling, reconnect your battery and verify the light to validate the achievement of the procedure.
.
How to replace the number plate bulb on your Ram ProMaster without outside access
Second section of our content, swap this license plate bulb on your Ram ProMaster without external access. Most often you will be able to access it, however some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Ram ProMaster
To change the one on the front plate, nothing could be less difficult, you will have to position yourself under the motor vehicle (ideally placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in general kept by two soft plastic tabs by pressing on both at the same time, then once you have your license plate bulb block in hand, Take out the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take care not to exert too much pressure otherwise you will break the plastic cover), and you will simply have to take off the burnt-out license plate bulb and change it with the new , then test and reassemble the whole thing.
How to change the rear license plate bulb on my Ram ProMaster
Finally last possibility, you must change the bulb on the backplate of your Ram ProMaster, but you are not able to open the cover from the outside of your motor vehicle. In this case, here is the process to accomplish this task:
- Unplug the battery from your Ram ProMaster
- Locate the spot of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever gently on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, unplug the holders for much easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Ram ProMaster, verify it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have discovered the main methods for changing license plate bulbs on your car, be aware that on some models the methodology may be a bit different but you should be able to accomplish it following the explanation of this article content. If you can’t do it, don’t hesitate to go to your garage area it would be a shame to break a part of your Ram ProMaster. If you want to change other bulbs like the position light bulbs on your Ram ProMaster or the low beam bulbs on Ram ProMaster, don’t hesitate to consult our content articles which explain you the operation to follow.
If you wish more tutorials on the Ram ProMaster, go to our Ram ProMaster category.
