Whether it’s for your specific safety, for roadworthiness tests or to avoid a fine, being certain your headlamp bulbs are all the time operational is necessary. In fact, bulbs are wearing units that will undoubtedly burn out over the years and as a result need to be swapped out. You’re most certainly here because one of your parking lights is burnt out and you’re wondering how to change your Land Rover Range Rover’s license plate bulb, we’ve made this content page to help you do it on your own and not have to go to your technician. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Land Rover Range Rover.
How to replace the license plate bulb on your Land Rover Range Rover through the outside
This method is the least difficult of the two, in fact, for this one you will just have to remove the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the situation we will spend some time on in the second part of this article content to explain the way.
So let’s begin with replacing the number plate bulb by going through the outside of your Land Rover Range Rover. Whether it’s the front or the back of your motor vehicle the technique will be the same.
Here are a few simple guidelines to stick to to conduct this service:
- With the engine off, disconnect the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to place the flat part into the notch assigned for this intent (in most cases on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Land Rover Range Rover
- Use your screwdriver or knife to remove the bulb from its location, in the event you are worried of breaking something, you can as well do it with your fingers.
- Finally, put the new license plate light bulb
- Last step, before reassembling, reconnect your battery and test the light to validate the successfulness of the operation.
.
How to replace the number plate bulb on your Land Rover Range Rover without outside access
Second part of our content, swap this license plate bulb on your Land Rover Range Rover without external access. In most cases you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to replace the front license plate bulb on my Land Rover Range Rover
To replace the one on the front plate, nothing could be less complicated, you will have to put yourself under the motor vehicle (preferably placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in most cases held by two soft plastic tabs by pressing on both simultaneously, then right after you have your license plate bulb block in hand, Take out the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be attentive not to put in too much force or you will break the plastic cover), and you will just have to remove the burnt-out license plate bulb and replace it with the new , then check and reassemble the whole thing.
How to replace the rear license plate bulb on my Land Rover Range Rover
Finally last solution, you must replace the bulb on the backplate of your Land Rover Range Rover, but you cannot really open the cover from the outside of your motor vehicle. In such a case, here is the tactic to perform this task:
- Unplug the battery from your Land Rover Range Rover
- Find the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever carefully on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, disconnect the holders for easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Land Rover Range Rover, test it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have learned the main approaches for replacing license plate bulbs on your car, be aware that on some models the methodology may be a bit different but you should be able to accomplish it following the outline of this article. If you can’t do it, don’t be reluctant to go to your garage area it would be a shame to break a part of your Land Rover Range Rover. If you want to change other bulbs like the position light bulbs on your Land Rover Range Rover or the low beam bulbs on Land Rover Range Rover, don’t be reluctant to consult our content articles which explain you the operation to follow.
If you want more guides on the Land Rover Range Rover, go to our Land Rover Range Rover category.
