Regardless it’s for your own personal safety, for roadworthiness tests or to avoid a fine, ensuring that your headlamp bulbs are all the time working is very important. In reality, bulbs are wearing parts that will predictably burn out over the years and as a result need to be changed. You’re quite likely in this article because one of your parking lights is burnt out and you’re wanting to know how to change your Land Rover LR4’s license plate bulb, we’ve written this document to help you do it by yourself and not have to go to your motor mechanic. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Land Rover LR4.
How to replace the license plate bulb on your Land Rover LR4 coming from the outside
This option is the most simple of the two, actually, for this one you will only require to remove the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the case we will take some time on in the second section of this document to clarify the way.
So let’s start with swapping the number plate bulb by going through the outside of your Land Rover LR4. Regardless it’s the front or the back of your motor vehicle the procedure will be the same.
Here are a few simple steps to follow to carry out this maintenance tasks:
- With the engine off, disconnect the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to insert the flat part into the notch specified for this purpose (almost always on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Land Rover LR4
- Use your screwdriver or knife to eject the bulb from its spot, if you are scared of breaking anything, you can as well do it with your fingers.
- Finally, position the new license plate light bulb
- Last step, before reassembling, reconnect your battery and test the light to confirm the success of the process.
.
How to replace the number plate bulb on your Land Rover LR4 without outside access
Second section of our item, swap this license plate bulb on your Land Rover LR4 without external access. Generally you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to replace the front license plate bulb on my Land Rover LR4
To replace the one on the front plate, nothing could be less difficult, you will have to position yourself under the motor vehicle (ideally put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, almost always kept by two soft plastic tabs by pressing on both at the same time, then now that you have your license plate bulb block in hand, Take away the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be mindful not to apply too much pressure or you will break the plastic cover), and you will simply have to remove the burnt-out license plate bulb and replace it with the new , then verify and reassemble the whole thing.
How to replace the rear license plate bulb on my Land Rover LR4
Finally last solution, you must replace the bulb on the backplate of your Land Rover LR4, but you cannot really open the cover from the outside of your motor vehicle. In this case, here is the process to operate this operation:
- Disconnect the battery from your Land Rover LR4
- Identify the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever softly on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, disconnect the holders for easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Land Rover LR4, test it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have discovered the main techniques for swapping license plate bulbs on your car, take note that on some models the methodology may be a bit different but you should be able to realize it following the explanation of this content. If you can’t do it, don’t hesitate to go to your mechanic it would be a shame to break a part of your Land Rover LR4. If you want to change other bulbs like the position light bulbs on your Land Rover LR4 or the low beam bulbs on Land Rover LR4, don’t hesitate to read our articles which describe you the operation to follow.
If perhaps you have any additional questions about the Land Rover LR4, do not hesitate to consult our Land Rover LR4 category.
