Regardless it’s for your specific security, for roadworthiness tests or to avoid a fine, being certain your headlamp bulbs are in every case working is necessary. In fact, bulbs are wearing units that will surely burn out after some time and as a consequence need to be changed. You’re quite likely on the website because one of your parking lights is burnt out and you’re struggling with how to change your Jeep Renegade’s license plate bulb, we’ve written and published this article content to help you do it without any help and not have to go to your auto technician. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Jeep Renegade.
How to swap the license plate bulb on your Jeep Renegade through the outside
This technique is the easiest of the two, in reality, for this one you will only require to take off the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the case we will dedicate a moment on in the second part of this content to describe the method.
So let’s start with replacing the number plate bulb by going through the outside of your Jeep Renegade. Regardless it’s the front or the back of your automobile the method will be similar.
Here are a few simple steps to follow to execute this maintenance:
- With the engine off, disconnect the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to insert the flat part into the notch supplied for this purpose (in most cases on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Jeep Renegade
- Use your screwdriver or knife to eject the bulb from its place, if you are afraid of destroying anything, you can also do it with your fingers.
- Finally, position the new license plate light bulb
- Last step, before reassembling, reconnect your battery and test the light to validate the achievement of the operation.
.
How to replace the number plate bulb on your Jeep Renegade without outside access
Second part of our content, change this license plate bulb on your Jeep Renegade without external access. Generally you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my Jeep Renegade
To swap the one on the front plate, nothing could be easier, you will have to position yourself under the automobile (preferably positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in most cases kept by two soft plastic tabs by pressing on both at once, then right after you have your license plate bulb block in hand, Remove the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be mindful not to put in too much force or you will break the plastic cover), and you will just have to take off the burnt-out license plate bulb and swap it with the new , then verify and reassemble the whole thing.
How to swap the rear license plate bulb on my Jeep Renegade
Finally last possibility, you must swap the bulb on the backplate of your Jeep Renegade, but you simply cannot open the cover from the outside of your automobile. In such a case, here is the solution to carry out this task:
- Unplug the battery from your Jeep Renegade
- Identify the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever gently on all the frame of the trunk to remove it.
- Once located, before removing the bulb holders, disconnect the holders for less complicated access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Jeep Renegade, test it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have learned the main tactics for replacing license plate bulbs on your car, take notice that on some models the methodology may be a bit different but you should be able to realize it following the outline of this document. If you can’t do it, don’t be reluctant to go to your mechanic it would be a shame to break a part of your Jeep Renegade. If you wish to change other bulbs like the position light bulbs on your Jeep Renegade or the low beam bulbs on Jeep Renegade, don’t be reluctant to read our articles which describe you the procedure to follow.
Whenever you have any additional questions about the Jeep Renegade, do not hesitate to consult our Jeep Renegade category.
