It doesn’t matter if it’s for your personal safety, for roadworthiness tests or to avoid a fine, being sure your headlamp bulbs are all the time effective is very important. Indeed, bulbs are wearing units that will surely burn out after awhile and therefore need to be swapped out. You’re most certainly on this site because one of your parking lights is burnt out and you’re struggling with how to change your Jeep Cherokee’s license plate bulb, we’ve made this document to help you do it on your own and not have to go to your mechanic. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Jeep Cherokee.
How to change the license plate bulb on your Jeep Cherokee coming from the outside
This method is the simplest of the two, actually, for this one you will only require to take away the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the situation we will dedicate a moment on in the second section of this article content to show you the approach.
So let’s start with replacing the number plate bulb by going through the outside of your Jeep Cherokee. It doesn’t matter if it’s the front or the back of your motor vehicle the technique will be the same.
Here are a few simple actions to follow to perform this service:
- With the engine off, unplug the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to insert the flat part into the notch specified for this purpose (in most cases on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Jeep Cherokee
- Use your screwdriver or knife to eject the bulb from its spot, in the event you are scared of destroying anything, you can as well do it with your fingers.
- Finally, position the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and test the light to validate the successfulness of the process.
.
How to change the number plate bulb on your Jeep Cherokee without outside access
Second section of our content page, swap this license plate bulb on your Jeep Cherokee without external access. Generally you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Jeep Cherokee
To change the one on the front plate, nothing could be less difficult, you will have to position yourself under the motor vehicle (preferably positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in most cases kept by two soft plastic tabs by pressing on both at the same time, then now that you have your license plate bulb block in hand, Take off the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be cautious not to put in too much force or you will break the plastic cover), and you will just have to take away the burnt-out license plate bulb and change it with the new , then check and reassemble the whole thing.
How to change the rear license plate bulb on my Jeep Cherokee
Finally last possibility, you must change the bulb on the backplate of your Jeep Cherokee, but you simply cannot open the cover from the outside of your motor vehicle. In such a case, here is the tactic to do this task:
- Unplug the battery from your Jeep Cherokee
- Identify the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever delicately on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, unplug the holders for much easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Jeep Cherokee, test it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have found out the main tactics for replacing license plate bulbs on your car, remember that on some models the method may be a bit different but you should be able to accomplish it following the explanation of this article. If you can’t do it, don’t hesitate to go to your mechanic it would be a shame to break a part of your Jeep Cherokee. If you desire to change other bulbs like the position light bulbs on your Jeep Cherokee or the low beam bulbs on Jeep Cherokee, don’t hesitate to browse our articles which demonstrate you the process to follow.
To discover more tips on the Jeep Cherokee, take a look at the Jeep Cherokee category.
