Whether it’s for your specific security, for roadworthiness tests or to avoid a fine, being certain your headlamp bulbs are in every case working is fundamental. Indeed, bulbs are wearing units that will undoubtedly burn out over the years and as a consequence need to be swapped out. You’re perhaps in this article because one of your parking lights is burnt out and you’re wondering how to change your Hyundai Kona’s license plate bulb, we’ve written this article to help you do it without any help and not have to go to your auto mechanic. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Hyundai Kona.
How to swap the license plate bulb on your Hyundai Kona coming from the outside
This process is the quickest of the two, in fact, for this one you will only have to take off the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the case we will take some time on in the second part of this article to clarify the way.
So let’s begin with replacing the number plate bulb by going through the outside of your Hyundai Kona. Whether it’s the front or the back of your automobile the procedure will be the same.
Here are a few simple steps to follow to carry out this routine service:
- With the engine off, disconnect the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch assigned for this intent (generally on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Hyundai Kona
- Use your screwdriver or knife to remove the bulb from its place, in the event that you are worried of breaking something, you can also do it with your fingers.
- Finally, position the new license plate light bulb
- Last step, before reassembling, reconnect your battery and verify the light to validate the success of the process.
.
How to replace the number plate bulb on your Hyundai Kona without outside access
Second part of our content, replace this license plate bulb on your Hyundai Kona without external access. Generally you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my Hyundai Kona
To swap the one on the front plate, nothing could be easier, you will have to position yourself under the automobile (ideally positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, generally held by two soft plastic tabs by pressing on both at once, then once you have your license plate bulb block in hand, Take out the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take extra care not to put in too much force otherwise you will break the plastic cover), and you will only have to take off the burnt-out license plate bulb and replace it with the new , then test and reassemble the whole thing.
How to swap the rear license plate bulb on my Hyundai Kona
Finally last option, you must swap the bulb on the backplate of your Hyundai Kona, but you simply cannot open the cover from the outside of your automobile. In such a case, here is the tactic to accomplish this operation:
- Disconnect the battery from your Hyundai Kona
- Identify the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever softly on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, disconnect the holders for much easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Hyundai Kona, verify it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have learned the main techniques for replacing license plate bulbs on your car, be aware that on some models the method may be a bit different but you should be able to realize it following the outline of this document. If you can’t do it, don’t be reluctant to go to your garage it would be a shame to break a part of your Hyundai Kona. If you want to change other bulbs like the position light bulbs on your Hyundai Kona or the low beam bulbs on Hyundai Kona, don’t be reluctant to browse our articles which explain you the operation to follow.
To discover more tips on the Hyundai Kona, take a look at the Hyundai Kona category.
