It doesn’t matter if it’s for your specific security, for roadworthiness tests or to avoid a fine, ensuring your headlamp bulbs are always operational is extremely important. Indeed, bulbs are wearing auto parts that will obviously burn out in the future and as a consequence need to be replaced. You’re probably on this site because one of your parking lights is burnt out and you’re wondering how to change your Honda Ridgeline’s license plate bulb, we’ve written and published this content to help you do it by yourself and not have to go to your technician. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Honda Ridgeline.
How to change the license plate bulb on your Honda Ridgeline through the outside
This process is the quickest of the two, actually, for this one you will just need to take off the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the case we will spend a moment on in the second part of this document to demonstrate the way.
So let’s begin with swapping the number plate bulb by going through the outside of your Honda Ridgeline. It doesn’t matter if it’s the front or the back of your automobile the process will be identical.
Here are a few simple guidelines to stick to to carry out this service:
- With the engine off, unplug the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch specified for this intent (in general on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Honda Ridgeline
- Use your screwdriver or knife to remove the bulb from its placement, in the event you are worried of breaking anything, you can as well do it with your fingers.
- Finally, position the new license plate light bulb
- Last step, before reassembling, reconnect your battery and verify the light to validate the achievement of the operation.
.
How to change the number plate bulb on your Honda Ridgeline without outside access
Second part of our item, replace this license plate bulb on your Honda Ridgeline without external access. In most cases you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Honda Ridgeline
To change the one on the front plate, nothing could be easier, you will have to position yourself under the automobile (preferably put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in general held by two soft plastic tabs by pressing on both at once, then now that you have your license plate bulb block in hand, Remove the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take extra care not to exert too much pressure or you will break the plastic cover), and you will just have to take off the burnt-out license plate bulb and swap it with the new , then test out and reassemble the whole thing.
How to change the rear license plate bulb on my Honda Ridgeline
Finally last option, you must change the bulb on the backplate of your Honda Ridgeline, but you cannot open the cover from the outside of your automobile. In such a case, here is the technique to do this operation:
- Unplug the battery from your Honda Ridgeline
- Locate the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever delicately on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, unplug the holders for much easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Honda Ridgeline, verify it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have discovered the main solutions for swapping license plate bulbs on your car, be aware that on some models the methodology may be a bit different but you should be able to accomplish it following the outline of this content. If you can’t do it, don’t hesitate to go to your mechanic it would be a shame to break a part of your Honda Ridgeline. If you need to change other bulbs like the position light bulbs on your Honda Ridgeline or the low beam bulbs on Honda Ridgeline, don’t hesitate to read our articles which explain you the procedure to follow.
If perhaps you have any additional questions about the Honda Ridgeline, do not hesitate to consult our Honda Ridgeline category.
