Regardless it’s for your personal safety, for roadworthiness testing or to avoid a fine, being sure your headlamp bulbs are always functioning is extremely important. In reality, bulbs are wearing units that will inevitably burn out after some time and consequently need to be swapped out. You’re almost certainly on this website because one of your parking lights is burnt out and you’re struggling with how to change your Scion xB’s license plate bulb, we’ve made this content to help you do it without any help and not have to go to your auto mechanic. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Scion xB.
How to swap the license plate bulb on your Scion xB coming from the outside
This tactic is the most simple of the two, in fact, for this one you will simply have to take out the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the case we will spend a moment on in the second section of this article content to explain the approach.
So let’s begin with changing the number plate bulb by going through the outside of your Scion xB. Regardless it’s the front or the back of your automobile the technique will be similar.
Here are a few simple guidelines to stick to to perform this routine service:
- With the engine turned off, disconnect the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to place the flat part into the notch specified for this goal (almost always on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Scion xB
- Use your screwdriver or knife to eject the bulb from its location, in the event you are afraid of breaking a thing, you can as well do it with your fingers.
- Finally, put the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and verify the light to validate the achievement of the task.
.
How to replace the number plate bulb on your Scion xB without outside access
Second section of our article, swap this license plate bulb on your Scion xB without external access. In most cases you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my Scion xB
To swap the one on the front plate, nothing could be much easier, you will have to put yourself under the automobile (ideally positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, almost always held by two soft plastic tabs by pressing on both at the same time, then once you have your license plate bulb block in hand, Remove the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take care not to put in too much pressure otherwise you will break the plastic cover), and you will just have to take out the burnt-out license plate bulb and swap it with the new , then test out and reassemble the whole thing.
How to swap the rear license plate bulb on my Scion xB
Finally last option, you must swap the bulb on the backplate of your Scion xB, but you cannot really open the cover from the outside of your automobile. In this instance, here is the process to perform this task:
- Unplug the battery from your Scion xB
- Identify the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever gently on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, disconnect the holders for less difficult access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Scion xB, verify it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have learned the main solutions for changing license plate bulbs on your car, be aware that on some models the technique may be a bit different but you should be able to accomplish it following the outline of this article. If you can’t do it, don’t hesitate to go to your mechanic it would be a shame to break a part of your Scion xB. If you desire to change other bulbs like the position light bulbs on your Scion xB or the low beam bulbs on Scion xB, don’t hesitate to read our content articles which describe you the operation to follow.
To get more tips on the Scion xB, take a look at the Scion xB category.
