Regardless whether it’s for your specific security, for roadworthiness tests or to avoid a fine, being sure your headlamp bulbs are constantly working is very important. In fact, bulbs are wearing auto parts that will predictably burn out over the years and therefore need to be changed. You’re most likely on this site because one of your parking lights is burnt out and you’re struggling with how to change your Ford S-max’s license plate bulb, we’ve created this document to help you do it on your own and not have to go to your mechanic. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Ford S-max.


How to replace the license plate bulb on your Ford S-max coming from the outside

This tactic is the most simple of the two, in fact, for this one you will simply require to take away the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the case we will take a moment on in the second section of this content page to show you the approach.
So let’s start with replacing the number plate bulb by going through the outside of your Ford S-max. Regardless whether it’s the front or the back of your motor vehicle the operation will be the same.
Here are a few simple guidelines to follow to perform this routine service:

  • With the engine off, disconnect the battery terminals from your car
  • Face your license plate and use a flat screwdriver or knife to insert the flat part into the notch assigned for this goal (in general on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Ford S-max
  • .

  • Use your screwdriver or knife to eject the bulb from its spot, in the event you are afraid of breaking something, you can also do it with your fingers.
  • Finally, position the new license plate light bulb
  • Last stage, before reassembling, reconnect your battery and verify the light to validate the achievement of the procedure.

How to change the number plate bulb on your Ford S-max without outside access

Second section of our document, replace this license plate bulb on your Ford S-max without external access. Generally you will be able to access it, nevertheless some series (often at the rear does not allow this access).

How to replace the front license plate bulb on my Ford S-max

To replace the one on the front plate, nothing could be less complicated, you will have to position yourself under the motor vehicle (ideally put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in general kept by two soft plastic tabs by pressing on both simultaneously, then right after you have your license plate bulb block in hand, Remove the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take care not to apply too much force otherwise you will break the plastic cover), and you will simply have to take away the burnt-out license plate bulb and change it with the new , then verify and reassemble the whole thing.

How to replace the rear license plate bulb on my Ford S-max

Finally last option, you must replace the bulb on the backplate of your Ford S-max, but you simply cannot open the cover from the outside of your motor vehicle. In this instance, here is the process to operate this task:

  • Unplug the battery from your Ford S-max
  • Find the location of your light bulbs from the outside.
  • From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever carefully on all the frame of the trunk to remove it.
  • Once located, before removing the bulb holders, disconnect the holders for less complicated access.
  • Using a screwdriver, lever the two plastic parts to remove the bulb holder
  • .

  • Replace the burnt-out license plate bulb on your Ford S-max, verify it and reassemble it, watching the clips on the trunk liner

There you have it, you have found out the main approaches for replacing license plate bulbs on your car, bear in mind that on some models the technique may be a bit different but you should be able to accomplish it following the outline of this article. If you can’t do it, don’t be reluctant to go to your workshop it would be a shame to break a part of your Ford S-max. If you need to change other bulbs like the position light bulbs on your Ford S-max or the low beam bulbs on Ford S-max, don’t be reluctant to browse our content articles which describe you the process to follow.

Whenever you have any further questions about the Ford S-max, do not hesitate to consult our Ford S-max category.