Whether it’s for your personal security, for roadworthiness testing or to avoid a fine, ensuring your headlamp bulbs are always functioning is very important. Indeed, bulbs are wearing units that will surely burn out with time and as a consequence need to be swapped out. You’re probably on this site because one of your parking lights is burnt out and you’re wondering how to change your Fiat Panda’s license plate bulb, we’ve created this document to help you do it on your own and not have to go to your auto mechanic. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Fiat Panda.

change-license-plate-bulb-fiat-panda

How to change the license plate bulb on your Fiat Panda through the outside

This tactic is the most simple of the two, in truth, for this one you will only require to take away the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the case we will take some time on in the second section of this content page to teach you the approach.
So let’s begin with replacing the number plate bulb by going through the outside of your Fiat Panda. Whether it’s the front or the back of your automobile the technique will be similar.
Here are a few simple steps to stick to to execute this maintenance:

  • With the engine turned off, unplug the battery terminals from your car
  • Face your license plate and use a flat screwdriver or knife to place the flat part into the notch supplied for this intent (in most cases on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Fiat Panda
  • .

  • Use your screwdriver or knife to remove the bulb from its location, in the event that you are scared of breaking a thing, you can as well do it with your fingers.
  • Finally, put the new license plate light bulb
  • Last step, before reassembling, reconnect your battery and check the light to confirm the success of the process.

How to replace the number plate bulb on your Fiat Panda without outside access

Second section of our item, swap this license plate bulb on your Fiat Panda without external access. In most cases you will be able to access it, nevertheless some series (often at the rear does not allow this access).

How to change the front license plate bulb on my Fiat Panda

To change the one on the front plate, nothing could be less difficult, you will have to put yourself under the automobile (ideally placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in most cases held by two soft plastic tabs by pressing on both simultaneously, then now that you have your license plate bulb block in hand, Take off the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take care not to put in too much pressure otherwise you will break the plastic cover), and you will just have to take away the burnt-out license plate bulb and swap it with the new , then verify and reassemble the whole thing.

How to change the rear license plate bulb on my Fiat Panda

Finally last possibility, you must change the bulb on the backplate of your Fiat Panda, but you cannot open the cover from the outside of your automobile. In this instance, here is the process to conduct this task:

  • Disconnect the battery from your Fiat Panda
  • Locate the position of your light bulbs from the outside.
  • From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever gently on all the frame of the trunk to remove it.
  • Once established, before removing the bulb holders, unplug the holders for less complicated access.
  • Using a screwdriver, lever the two plastic parts to remove the bulb holder
  • .

  • Change the burnt-out license plate bulb on your Fiat Panda, check it and reassemble it, watching the clips on the trunk liner

.
There you have it, you have discovered the main approaches for replacing license plate bulbs on your car, be aware that on some models the method may be a bit different but you should be able to realize it following the outline of this article content. If you can’t do it, don’t hesitate to go to your garage area it would be a shame to break a part of your Fiat Panda. If you desire to change other bulbs like the position light bulbs on your Fiat Panda or the low beam bulbs on Fiat Panda, don’t hesitate to read our content articles which describe you the procedure to follow.

If you wish more tutorials on the Fiat Panda, go to our Fiat Panda category.