Regardless whether it’s for your personal security, for roadworthiness tests or to avoid a fine, making sure your headlamp bulbs are in every case functional is necessary. In fact, bulbs are wearing units that will inevitably burn out over the years and consequently need to be replaced. You’re likely on this site because one of your parking lights is burnt out and you’re struggling with how to change your Ds Ds 3 Crossback’s license plate bulb, we’ve made this article to help you do it by yourself and not have to go to your auto technician. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Ds Ds 3 Crossback.
How to change the license plate bulb on your Ds Ds 3 Crossback throughout the outside
This process is the simplest of the two, actually, for this one you will just need to take off the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the case we will dedicate a moment on in the second part of this content page to teach you the method.
So let’s begin with swapping the number plate bulb by going through the outside of your Ds Ds 3 Crossback. Regardless whether it’s the front or the back of your motor vehicle the operation will be the same.
Here are a few simple steps to stick to to carry out this service:
- With the engine off, unplug the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch assigned for this intent (almost always on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Ds Ds 3 Crossback
- Use your screwdriver or knife to eject the bulb from its place, if you are worried of breaking a thing, you can as well do it with your fingers.
- Finally, put the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and verify the light to confirm the successfulness of the process.
.
How to replace the number plate bulb on your Ds Ds 3 Crossback without outside access
Second part of our content page, change this license plate bulb on your Ds Ds 3 Crossback without external access. Generally you will be able to access it, but some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Ds Ds 3 Crossback
To change the one on the front plate, nothing could be much easier, you will have to put yourself under the motor vehicle (preferably positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, almost always held by two soft plastic tabs by pressing on both at once, then once you have your license plate bulb block in hand, Take off the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be careful not to put in too much force or you will break the plastic cover), and you will only have to take off the burnt-out license plate bulb and change it with the new , then check and reassemble the whole thing.
How to change the rear license plate bulb on my Ds Ds 3 Crossback
Finally last solution, you must change the bulb on the backplate of your Ds Ds 3 Crossback, but you cannot really open the cover from the outside of your motor vehicle. In this case, here is the approach to perform this operation:
- Unplug the battery from your Ds Ds 3 Crossback
- Identify the spot of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever softly on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, unplug the holders for less complicated access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Ds Ds 3 Crossback, verify it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have found out the main techniques for swapping license plate bulbs on your car, take notice that on some models the technique may be a bit different but you should be able to accomplish it following the explanation of this document. If you can’t do it, don’t be reluctant to go to your mechanic it would be a shame to break a part of your Ds Ds 3 Crossback. If you need to change other bulbs like the position light bulbs on your Ds Ds 3 Crossback or the low beam bulbs on Ds Ds 3 Crossback, don’t be reluctant to browse our content articles which demonstrate you the process to follow.
If you have any further questions about the Ds Ds 3 Crossback, do not hesitate to consult our Ds Ds 3 Crossback category.
