Regardless whether it’s for your personal security, for roadworthiness tests or to avoid a fine, making sure your headlamp bulbs are constantly working is fundamental. In reality, bulbs are wearing parts that will surely burn out after awhile and as a result need to be swapped out. You’re probably on this website because one of your parking lights is burnt out and you’re worried about how to change your Dodge Nitro’s license plate bulb, we’ve written and published this content page to help you do it on your own and not have to go to your auto mechanic. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Dodge Nitro.
How to swap the license plate bulb on your Dodge Nitro throughout the outside
This tactic is the most simple of the two, in reality, for this one you will only require to take away the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the case we will dedicate a moment on in the second section of this document to describe the way.
So let’s begin with swapping the number plate bulb by going through the outside of your Dodge Nitro. Regardless whether it’s the front or the back of your automobile the operation will be identical.
Here are a few simple steps to follow to perform this routine service:
- With the engine turned off, disconnect the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch provided for this purpose (usually on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Dodge Nitro
- Use your screwdriver or knife to eject the bulb from its placement, in the event that you are afraid of destroying a thing, you can as well do it with your fingers.
- Finally, put the new license plate light bulb
- Last step, before reassembling, reconnect your battery and check the light to validate the successfulness of the process.
.
How to replace the number plate bulb on your Dodge Nitro without outside access
Second section of our article, swap this license plate bulb on your Dodge Nitro without external access. Generally you will be able to access it, however some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my Dodge Nitro
To swap the one on the front plate, nothing could be less complicated, you will have to put yourself under the automobile (ideally put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, usually kept by two soft plastic tabs by pressing on both at the same time, then right after you have your license plate bulb block in hand, Take away the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be attentive not to apply too much force or you will break the plastic cover), and you will simply have to take away the burnt-out license plate bulb and swap it with the new , then verify and reassemble the whole thing.
How to swap the rear license plate bulb on my Dodge Nitro
Finally last possibility, you must swap the bulb on the backplate of your Dodge Nitro, but you cannot really open the cover from the outside of your automobile. In this instance, here is the technique to conduct this operation:
- Disconnect the battery from your Dodge Nitro
- Find the spot of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever softly on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, disconnect the holders for less difficult access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Dodge Nitro, check it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have learned the main methods for swapping license plate bulbs on your car, bear in mind that on some models the methodology may be a bit different but you should be able to do it following the explanation of this document. If you can’t do it, don’t be reluctant to go to your garage it would be a shame to break a part of your Dodge Nitro. If you want to change other bulbs like the position light bulbs on your Dodge Nitro or the low beam bulbs on Dodge Nitro, don’t be reluctant to consult our content articles which describe you the process to follow.
To get more tips on the Dodge Nitro, take a look at the Dodge Nitro category.
