Regardless whether it’s for your personal security, for roadworthiness tests or to avoid a fine, making sure your headlamp bulbs are constantly functional is necessary. In reality, bulbs are wearing parts that will predictably burn out after awhile and therefore need to be replaced. You’re almost certainly in this article because one of your parking lights is burnt out and you’re wanting to know how to change your Chevrolet Colorado’s license plate bulb, we’ve created this document to help you do it by yourself and not have to go to your technician. Firstly, we will take a look at changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Chevrolet Colorado.
How to change the license plate bulb on your Chevrolet Colorado throughout the outside
This approach is the easiest of the two, in fact, for this one you will simply have to take away the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the case we will spend a moment on in the second section of this article to explain the method.
So let’s begin with replacing the number plate bulb by going through the outside of your Chevrolet Colorado. Regardless whether it’s the front or the back of your motor vehicle the technique will be the same.
Here are a few simple guidelines to stick to to perform this service:
- With the engine turned off, unplug the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch assigned for this intent (usually on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Chevrolet Colorado
- Use your screwdriver or knife to remove the bulb from its placement, if you are afraid of damaging anything, you can also do it with your fingers.
- Finally, position the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and verify the light to validate the achievement of the task.
.
How to change the number plate bulb on your Chevrolet Colorado without outside access
Second section of our document, swap this license plate bulb on your Chevrolet Colorado without external access. In most cases you will be able to access it, but some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Chevrolet Colorado
To change the one on the front plate, nothing could be easier, you will have to position yourself under the motor vehicle (preferably put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, usually kept by two soft plastic tabs by pressing on both simultaneously, then right after you have your license plate bulb block in hand, Take off the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take extra care not to apply too much force otherwise you will break the plastic cover), and you will simply have to take away the burnt-out license plate bulb and replace it with the new , then verify and reassemble the whole thing.
How to change the rear license plate bulb on my Chevrolet Colorado
Finally last option, you must change the bulb on the backplate of your Chevrolet Colorado, but you simply cannot open the cover from the outside of your motor vehicle. In this case, here is the solution to accomplish this operation:
- Disconnect the battery from your Chevrolet Colorado
- Identify the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever carefully on all the frame of the trunk to remove it.
- Once located, before removing the bulb holders, unplug the holders for less complicated access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Chevrolet Colorado, verify it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have learned the main approaches for replacing license plate bulbs on your car, bear in mind that on some models the methodology may be a bit different but you should be able to do it following the explanation of this content. If you can’t do it, don’t hesitate to go to your mechanic it would be a shame to break a part of your Chevrolet Colorado. If you want to change other bulbs like the position light bulbs on your Chevrolet Colorado or the low beam bulbs on Chevrolet Colorado, don’t hesitate to read our content articles which describe you the operation to follow.
To get more tips on the Chevrolet Colorado, take a look at the Chevrolet Colorado category.
