Regardless it’s for your personal security, for roadworthiness tests or to avoid a fine, being sure your headlamp bulbs are always functioning is very important. In reality, bulbs are wearing parts that will predictably burn out with time and therefore need to be swapped out. You’re quite likely on the website because one of your parking lights is burnt out and you’re struggling with how to change your Chrysler Sebring’s license plate bulb, we’ve written and published this article content to help you do it by yourself and not have to go to your auto mechanic. Firstly, we will take a look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Chrysler Sebring.
How to swap the license plate bulb on your Chrysler Sebring through the outside
This method is the easiest of the two, actually, for this one you will just need to remove the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the case we will spend a moment on in the second section of this document to clarify the way.
So let’s begin with swapping the number plate bulb by going through the outside of your Chrysler Sebring. Regardless it’s the front or the back of your automobile the technique will be the same.
Here are a few simple actions to follow to carry out this routine service:
- With the engine turned off, disconnect the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch specified for this goal (almost always on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Chrysler Sebring
- Use your screwdriver or knife to remove the bulb from its placement, in the event you are afraid of destroying anything, you can as well do it with your fingers.
- Finally, position the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and verify the light to confirm the success of the process.
.
How to replace the number plate bulb on your Chrysler Sebring without outside access
Second section of our item, change this license plate bulb on your Chrysler Sebring without external access. In most cases you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my Chrysler Sebring
To swap the one on the front plate, nothing could be less hard, you will have to position yourself under the automobile (preferably put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, almost always kept by two soft plastic tabs by pressing on both simultaneously, then right after you have your license plate bulb block in hand, Take away the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take extra care not to apply too much pressure otherwise you will break the plastic cover), and you will simply have to remove the burnt-out license plate bulb and swap it with the new , then check and reassemble the whole thing.
How to swap the rear license plate bulb on my Chrysler Sebring
Finally last possibility, you must swap the bulb on the backplate of your Chrysler Sebring, but you cannot really open the cover from the outside of your automobile. In this case, here is the approach to perform this task:
- Unplug the battery from your Chrysler Sebring
- Identify the spot of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever delicately on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, disconnect the holders for less difficult access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Chrysler Sebring, verify it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have found out the main solutions for swapping license plate bulbs on your car, be aware that on some models the technique may be a bit different but you should be able to realize it following the explanation of this article. If you can’t do it, don’t hesitate to go to your garage it would be a shame to break a part of your Chrysler Sebring. If you need to change other bulbs like the position light bulbs on your Chrysler Sebring or the low beam bulbs on Chrysler Sebring, don’t hesitate to browse our content articles which describe you the operation to follow.
To get more tips on the Chrysler Sebring, take a look at the Chrysler Sebring category.
