It doesn’t matter if it’s for your personal safety, for roadworthiness tests or to avoid a fine, being sure your headlamp bulbs are constantly effective is fundamental. In fact, bulbs are wearing auto parts that will undoubtedly burn out over time and consequently need to be changed. You’re most likely on this website because one of your parking lights is burnt out and you’re struggling with how to change your Chrysler 200’s license plate bulb, we’ve made this article content to help you do it on your own and not have to go to your mechanic. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Chrysler 200.
How to swap the license plate bulb on your Chrysler 200 coming from the outside
This solution is the most simple of the two, actually, for this one you will just have to take off the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the situation we will take a moment on in the second part of this content to clarify the approach.
So let’s start with swapping the number plate bulb by going through the outside of your Chrysler 200. It doesn’t matter if it’s the front or the back of your automobile the technique will be the same.
Here are a few simple guidelines to stick to to perform this maintenance:
- With the engine turned off, disconnect the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to insert the flat part into the notch specified for this intent (in general on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Chrysler 200
- Use your screwdriver or knife to eject the bulb from its location, in the event that you are worried of destroying something, you can also do it with your fingers.
- Finally, position the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and verify the light to confirm the successfulness of the process.
.
How to replace the number plate bulb on your Chrysler 200 without outside access
Second part of our content page, replace this license plate bulb on your Chrysler 200 without external access. In most cases you will be able to access it, but some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my Chrysler 200
To swap the one on the front plate, nothing could be easier, you will have to position yourself under the automobile (ideally positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in general held by two soft plastic tabs by pressing on both at once, then right after you have your license plate bulb block in hand, Remove the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take extra care not to put in too much force otherwise you will break the plastic cover), and you will only have to take off the burnt-out license plate bulb and replace it with the new , then test and reassemble the whole thing.
How to swap the rear license plate bulb on my Chrysler 200
Finally last solution, you must swap the bulb on the backplate of your Chrysler 200, but you cannot really open the cover from the outside of your automobile. In this instance, here is the method to perform this operation:
- Disconnect the battery from your Chrysler 200
- Identify the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever delicately on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, disconnect the holders for less complicated access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Chrysler 200, verify it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have learned the main techniques for swapping license plate bulbs on your car, be aware that on some models the technique may be a bit different but you should be able to accomplish it following the explanation of this content page. If you can’t do it, don’t be reluctant to go to your garage it would be a shame to break a part of your Chrysler 200. If you want to change other bulbs like the position light bulbs on your Chrysler 200 or the low beam bulbs on Chrysler 200, don’t be reluctant to read our content articles which describe you the procedure to follow.
Whenever you have any additional questions about the Chrysler 200, do not hesitate to consult our Chrysler 200 category.
