Regardless it’s for your personal safety, for roadworthiness tests or to avoid a fine, being certain your headlamp bulbs are constantly effective is extremely important. In fact, bulbs are wearing auto parts that will undoubtedly burn out as time passes and consequently need to be replaced. You’re most likely in this article because one of your parking lights is burnt out and you’re questioning how to change your Chevrolet Impala’s license plate bulb, we’ve made this content to help you do it by yourself and not have to go to your technician. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Chevrolet Impala.
How to change the license plate bulb on your Chevrolet Impala throughout the outside
This technique is the simplest of the two, in fact, for this one you will simply need to take away the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the situation we will take some time on in the second part of this article to demonstrate the method.
So let’s start with swapping the number plate bulb by going through the outside of your Chevrolet Impala. Regardless it’s the front or the back of your motor vehicle the method will be identical.
Here are a few simple actions to follow to execute this maintenance:
- With the engine turned off, disconnect the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to place the flat part into the notch provided for this goal (generally on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Chevrolet Impala
- Use your screwdriver or knife to eject the bulb from its place, in the event that you are scared of breaking anything, you can also do it with your fingers.
- Finally, position the new license plate light bulb
- Last step, before reassembling, reconnect your battery and verify the light to validate the achievement of the operation.
.
How to replace the number plate bulb on your Chevrolet Impala without outside access
Second part of our content, change this license plate bulb on your Chevrolet Impala without external access. In most cases you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Chevrolet Impala
To change the one on the front plate, nothing could be less complicated, you will have to position yourself under the motor vehicle (preferably placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, generally held by two soft plastic tabs by pressing on both simultaneously, then once you have your license plate bulb block in hand, Remove the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be mindful not to apply too much pressure otherwise you will break the plastic cover), and you will just have to take away the burnt-out license plate bulb and change it with the new , then check and reassemble the whole thing.
How to change the rear license plate bulb on my Chevrolet Impala
Finally last solution, you must change the bulb on the backplate of your Chevrolet Impala, but you cannot open the cover from the outside of your motor vehicle. In such a case, here is the tactic to carry out this task:
- Disconnect the battery from your Chevrolet Impala
- Identify the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever carefully on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, disconnect the holders for less difficult access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Chevrolet Impala, verify it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have learned the main approaches for swapping license plate bulbs on your car, remember that on some models the method may be a bit different but you should be able to do it following the explanation of this article. If you can’t do it, don’t be reluctant to go to your mechanic it would be a shame to break a part of your Chevrolet Impala. If you want to change other bulbs like the position light bulbs on your Chevrolet Impala or the low beam bulbs on Chevrolet Impala, don’t be reluctant to consult our content articles which demonstrate you the procedure to follow.
To find more tips on the Chevrolet Impala, take a look at the Chevrolet Impala category.
