Regardless it’s for your own security, for roadworthiness testing or to avoid a fine, making sure your headlamp bulbs are constantly operational is fundamental. In fact, bulbs are wearing units that will obviously burn out over time and as a consequence need to be replaced. You’re most likely on the website because one of your parking lights is burnt out and you’re wondering how to change your Toyota Sienna’s license plate bulb, we’ve created this content page to help you do it on your own and not have to go to your technician. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Toyota Sienna.

change-license-plate-bulb-toyota-sienna

How to swap the license plate bulb on your Toyota Sienna throughout the outside

This tactic is the easiest of the two, in truth, for this one you will just require to take away the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the situation we will spend some time on in the second section of this content to show you the way.
So let’s begin with replacing the number plate bulb by going through the outside of your Toyota Sienna. Regardless it’s the front or the back of your automobile the procedure will be identical.
Here are a few simple guidelines to follow to execute this maintenance tasks:

  • With the engine turned off, disconnect the battery terminals from your car
  • Face your license plate and use a flat screwdriver or knife to place the flat part into the notch assigned for this purpose (almost always on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Toyota Sienna
  • .

  • Use your screwdriver or knife to remove the bulb from its location, in the event that you are afraid of breaking a thing, you can also do it with your fingers.
  • Finally, put the new license plate light bulb
  • Last stage, before reassembling, reconnect your battery and check the light to validate the achievement of the procedure.

How to change the number plate bulb on your Toyota Sienna without outside access

Second section of our item, swap this license plate bulb on your Toyota Sienna without external access. Most often you will be able to access it, however some series (often at the rear does not allow this access).

How to swap the front license plate bulb on my Toyota Sienna

To swap the one on the front plate, nothing could be easier, you will have to put yourself under the automobile (ideally positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, almost always kept by two soft plastic tabs by pressing on both at the same time, then right after you have your license plate bulb block in hand, Take away the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be mindful not to exert too much pressure or you will break the plastic cover), and you will only have to take away the burnt-out license plate bulb and replace it with the new , then check and reassemble the whole thing.

How to swap the rear license plate bulb on my Toyota Sienna

Finally last solution, you must swap the bulb on the backplate of your Toyota Sienna, but you simply cannot open the cover from the outside of your automobile. In this case, here is the solution to execute this operation:

  • Unplug the battery from your Toyota Sienna
  • Find the spot of your light bulbs from the outside.
  • From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever carefully on all the frame of the trunk to remove it.
  • Once established, before removing the bulb holders, disconnect the holders for less difficult access.
  • Using a screwdriver, lever the two plastic parts to remove the bulb holder
  • .

  • Change the burnt-out license plate bulb on your Toyota Sienna, check it and reassemble it, paying attention to the clips on the trunk liner

.
There you have it, you have learned the main approaches for replacing license plate bulbs on your car, take notice that on some models the technique may be a bit different but you should be able to realize it following the explanation of this content. If you can’t do it, don’t be reluctant to go to your workshop it would be a shame to break a part of your Toyota Sienna. If you desire to change other bulbs like the position light bulbs on your Toyota Sienna or the low beam bulbs on Toyota Sienna, don’t be reluctant to read our content articles which describe you the process to follow.

If you want more tutorials on the Toyota Sienna, go to our Toyota Sienna category.