Regardless whether it’s for your specific safety, for roadworthiness testing or to avoid a fine, ensuring your headlamp bulbs are all the time operational is very important. In fact, bulbs are wearing units that will undoubtedly burn out after some time and as a result need to be changed. You’re perhaps on this site because one of your parking lights is burnt out and you’re worried about how to change your Chevrolet Camaro’s license plate bulb, we’ve created this article content to help you do it without any help and not have to go to your motor mechanic. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Chevrolet Camaro.
How to change the license plate bulb on your Chevrolet Camaro throughout the outside
This tactic is the most simple of the two, in truth, for this one you will only require to take out the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the situation we will take some time on in the second section of this article to teach you the method.
So let’s begin with changing the number plate bulb by going through the outside of your Chevrolet Camaro. Regardless whether it’s the front or the back of your automobile the method will be the same.
Here are a few simple actions to follow to carry out this routine service:
- With the engine off, disconnect the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to insert the flat part into the notch assigned for this intent (commonly on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Chevrolet Camaro
- Use your screwdriver or knife to eject the bulb from its location, in the event you are worried of damaging something, you can also do it with your fingers.
- Finally, position the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and verify the light to validate the success of the procedure.
.
How to replace the number plate bulb on your Chevrolet Camaro without outside access
Second section of our item, replace this license plate bulb on your Chevrolet Camaro without external access. Generally you will be able to access it, but some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Chevrolet Camaro
To change the one on the front plate, nothing could be simpler, you will have to position yourself under the automobile (ideally positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, commonly kept by two soft plastic tabs by pressing on both simultaneously, then once you have your license plate bulb block in hand, Take out the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take extra care not to put in too much force otherwise you will break the plastic cover), and you will only have to take out the burnt-out license plate bulb and swap it with the new , then verify and reassemble the whole thing.
How to change the rear license plate bulb on my Chevrolet Camaro
Finally last option, you must change the bulb on the backplate of your Chevrolet Camaro, but you cannot open the cover from the outside of your automobile. In such a case, here is the solution to operate this operation:
- Disconnect the battery from your Chevrolet Camaro
- Locate the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever carefully on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, disconnect the holders for less complicated access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Chevrolet Camaro, verify it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have discovered the main tactics for changing license plate bulbs on your car, remember that on some models the methodology may be a bit different but you should be able to realize it following the explanation of this article content. If you can’t do it, don’t be reluctant to go to your workshop it would be a shame to break a part of your Chevrolet Camaro. If you need to change other bulbs like the position light bulbs on your Chevrolet Camaro or the low beam bulbs on Chevrolet Camaro, don’t be reluctant to browse our articles which explain you the procedure to follow.
If you have any further questions about the Chevrolet Camaro, do not hesitate to consult our Chevrolet Camaro category.
