It doesn’t matter if it’s for your own safety, for roadworthiness tests or to avoid a fine, being certain your headlamp bulbs are always functional is very important. Indeed, bulbs are wearing units that will surely burn out over time and as a result need to be swapped out. You’re perhaps in this article because one of your parking lights is burnt out and you’re worried about how to change your Audi S3’s license plate bulb, we’ve written this content to help you do it without any help and not have to go to your auto mechanic. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Audi S3.
How to change the license plate bulb on your Audi S3 throughout the outside
This technique is the easiest of the two, in truth, for this one you will simply need to remove the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the situation we will take some time on in the second section of this content page to explain the way.
So let’s begin with replacing the number plate bulb by going through the outside of your Audi S3. It doesn’t matter if it’s the front or the back of your vehicle the method will be identical.
Here are a few simple guidelines to follow to conduct this maintenance tasks:
- With the engine off, unplug the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch provided for this goal (usually on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Audi S3
- Use your screwdriver or knife to eject the bulb from its spot, in the event that you are worried of breaking anything, you can as well do it with your fingers.
- Finally, position the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and test the light to confirm the achievement of the operation.
.
How to change the number plate bulb on your Audi S3 without outside access
Second section of our article, change this license plate bulb on your Audi S3 without external access. In most cases you will be able to access it, however some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Audi S3
To change the one on the front plate, nothing could be simpler, you will have to position yourself under the vehicle (preferably put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, usually kept by two soft plastic tabs by pressing on both at the same time, then right after you have your license plate bulb block in hand, Remove the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be careful not to put in too much force otherwise you will break the plastic cover), and you will simply have to remove the burnt-out license plate bulb and swap it with the new , then test out and reassemble the whole thing.
How to change the rear license plate bulb on my Audi S3
Finally last solution, you must change the bulb on the backplate of your Audi S3, but you simply cannot open the cover from the outside of your vehicle. In this case, here is the tactic to perform this task:
- Disconnect the battery from your Audi S3
- Identify the spot of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever carefully on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, unplug the holders for less difficult access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Audi S3, test it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have found out the main tactics for replacing license plate bulbs on your car, be aware that on some models the technique may be a bit different but you should be able to realize it following the outline of this article. If you can’t do it, don’t hesitate to go to your workshop it would be a shame to break a part of your Audi S3. If you want to change other bulbs like the position light bulbs on your Audi S3 or the low beam bulbs on Audi S3, don’t hesitate to browse our content articles which explain you the process to follow.
Whenever you have any further questions about the Audi S3, do not hesitate to consult our Audi S3 category.
