When your car is running normally everything is fine, however if it starts to have regular problems you may start to question, especially if your motor vehicle won’t start. In this post we will show you where the starter of a Fiat Panda 3 is, it will help you to fix your ignition problems. To get this done, we will first illustrate the role of a starter, then, where is the starter on a Fiat Panda 3 , and, finally, how to replace the starter of a motor vehicle.
Role of the starter on your Fiat Panda 3
We start this article by explaining the role of the starter motor on your Fiat Panda 3. The starter is an electric motor which is powered by your battery, its function will be to make your engine run at a high enough speed to start it (usually around 300/400 rpm). It is composed of three main parts:
- The Solenoid: This part is an electrical relay that will work as a switch, it will be activated by the key of your Fiat Panda 3 and let the current from your battery to the engine of your alternator.
- The engagement pinion: This is the last component of your starter, it is the toothed wheel that will be in direct contact with the flywheel, it allows to transmit the force from the starter to the engine.
The engine: Most important component of your alternator, it is the one that will drive the flywheel of your Fiat Panda 3 and create enough speed for your engine to start.
Where is the starter on a Fiat Panda 3?
Now that we have quickly described what a starter is and how it works, we will answer the question that most of you have to ask yourselves where is the starter found on a Fiat Panda 3? It is quite easy to discover a starter, in fact, it is a large component that will almost always be situated in a similar location. We let you see the two possible places for your motor vehicle starter below.
Location of the starter on classic Fiat Panda 3
First and most basic circumstance, where to discover the starter of a Fiat Panda 3 with a conventional motor (implied without start and stop). The starter has a specific action, to start the engine of your motor vehicle, for that, it must always be near the engine flywheel of this one because it is the component that it actuates when it is used. The flywheel is found at the junction between your gearbox and your engine.
Location of the starter to Fiat Panda 3 with start and stop
And now second possible starter location of your Fiat Panda 3 . This case is much less frequent. It just concerns engines equipped with start and stop, and a good component of them will be equipped with a starter situated close to the flywheel. However, on some specific series or engines, the starter of your Fiat Panda 3 may be included in your alternator, it is then called a starter-alternator, to discover it nothing less difficult, identify your accessory belt and you should discover the big starter block.
How to replace the starter on a Fiat Panda 3?
Finally, we’ll explain to you quite quickly how to replace the starter of a Fiat Panda 3. This procedure is not necessarily difficult, it can be considered by people who have a minimum of basic mechanical expertise and adapted tools. Follow below the main steps to carry out this intervention:
- Disconnect the battery on your Fiat Panda 3, if you don’t know how to do it, don’t think twice to consult our article which details how to do it without taking any risk.
- After locating your starter, loosen the fasteners that hold it in your engine block, there will in most cases be 2 or 3
- It will be time to disconnect the power cables from the starter motor of your Fiat Panda 3, however before doing so we recommend you to take a picture of the installation to avoid making a mistake when reassembling.
- It’s possible that to remove it you may need to remove parts like the gimbal.
- Remount the new starter, being careful when connecting the connectors.
- Reconnect your battery and test your starter.
.
Whenever you have any further questions about the Fiat Panda 3, do not hesitate to consult our Fiat Panda 3 category.
