If you’re a bit of a do-it-yourselfer, you’re likely eager to look after the majority of the service to be achieved on your Skoda Enyaq, but some are more complicated than others and need the removal of body parts or elements to access the component you want to operate on. We want to help you in this process. That’s why today we are going to find out how to remove the bumper from a Skoda Enyaq. This process is not very complicated and you should be able to do it with few equipment. For that, first we will see how to remove the front bumper of your Skoda Enyaq, then how to remove the rear bumper of this one.
How to remove the front bumper from a Skoda Enyaq
So let’s commence our content with the front bumper of your Skoda Enyaq. To remove it, you will just need a set of ratchet wrenches, some screwdrivers and torx bits. Here are the steps you will have to follow to be able to disassemble the bumper of your Skoda Enyaq in good conditions:
- If you want to be more relaxed, we recommend you to lift your Skoda Enyaq and to remove the front wheels to have a good access to the whole front bumper.
- Open the bonnet of your vehicle: Seems evident, but you will need to have access to the bumper attachment in your engine compartment.
- Take off the wheel arches: They’re also identified as fenders, but they’ll get in the way and stop you from accessing all the screws on the front bumper of your Skoda Enyaq. Depending on your vehicle features and the year of your model, you will also have the ability to find staples, to accomplish this, you will just have to use a staple extractor or to do it gently with a big flat screwdriver, and use a lever to open the staple.
- Then you will have to unscrew the screws that is from behind your mudguard and that locks the front bumper of your Skoda Enyaq on the sides.
- Unscrew the screws or remove the clips on the upper part of the bumper in the engine compartment.
- Now it’s time to go beneath your Skoda Enyaq to unscrew the bolts that are on the chassis of the vehicle, you will find some in the middle of the bumper and on the sides.
- Be sure you unplug the connection of the plate lighting and the distance control sensor if you have it.
- Carefully remove the front bumper by first unclipping the sides. If it doesn’t come off, you most likely forgot a screw or a clip. Think of employing a carpet or other to prevent that it gets scratched by touching the ground.
That’s it, you’ve seen all the steps of how to remove the front bumper from your Skoda Enyaq, to put it back in place follow the steps in the opposite way.
How to remove the rear bumper from a Skoda Enyaq
And now, regardless if the process is quite equivalent, we will check out the case of removing the rear bumper from your Skoda Enyaq. For each stage to avoid repeating ourselves we will exclusively give you the broad outlines, refer to part 1 if you have any uncertainties or questions for more information.
- Start with executing the same first stage, that is, lift your Skoda Enyaq and take out your rear wheels to be able to have an ideal working space to remove the bumper of your Skoda Enyaq without trouble
- Remove the rear wheel arches of your Skoda Enyaq to access the side bumper side brackets
- Open your trunk
- Take off the side brackets in your wheel arches to make it easier to remove the bumper from your Skoda Enyaq.
- Take off the lower bindings below your Skoda Enyaq.
- At the same time, make sure disconnect the rear license plate light and the reverse radar sensors if you are equipped with them.
- Unscrew the top brackets from the top of the trunk.
- Now all you have to do is remove the rear bumper from your Skoda Enyaq, follow the same procedure as for the front bumper
Here, you have discoverd through these two parts, how to remove the bumper from a Skoda Enyaq whether it is the front one or the rear one the approaches are almost the same and it is enough to be careful to make everything go well.
Whenever you have any additional questions about the Skoda Enyaq, do not hesitate to consult our Skoda Enyaq category.
