Regardless it’s for your own personal security, for roadworthiness tests or to avoid a fine, ensuring that your headlamp bulbs are all the time functional is necessary. In reality, bulbs are wearing auto parts that will inevitably burn out over the years and as a consequence need to be swapped out. You’re probably on this site because one of your parking lights is burnt out and you’re questioning how to change your Toyota Venza’s license plate bulb, we’ve created this content page to help you do it without any help and not have to go to your auto mechanic. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Toyota Venza.
How to swap the license plate bulb on your Toyota Venza coming from the outside
This process is the simplest of the two, in reality, for this one you will only have to take out the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the situation we will dedicate some time on in the second part of this article content to demonstrate the approach.
So let’s start with replacing the number plate bulb by going through the outside of your Toyota Venza. Regardless it’s the front or the back of your vehicle the procedure will be identical.
Here are a few simple actions to follow to execute this service:
- With the engine off, disconnect the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to place the flat part into the notch provided for this intent (usually on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Toyota Venza
- Use your screwdriver or knife to eject the bulb from its place, in the event that you are worried of breaking a thing, you can as well do it with your fingers.
- Finally, put the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and test the light to confirm the success of the procedure.
.
How to replace the number plate bulb on your Toyota Venza without outside access
Second part of our content, change this license plate bulb on your Toyota Venza without external access. Most often you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my Toyota Venza
To swap the one on the front plate, nothing could be less difficult, you will have to put yourself under the vehicle (ideally positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, usually held by two soft plastic tabs by pressing on both simultaneously, then once you have your license plate bulb block in hand, Take out the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take extra care not to apply too much pressure otherwise you will break the plastic cover), and you will simply have to take out the burnt-out license plate bulb and change it with the new , then verify and reassemble the whole thing.
How to swap the rear license plate bulb on my Toyota Venza
Finally last solution, you must swap the bulb on the backplate of your Toyota Venza, but you cannot open the cover from the outside of your vehicle. In such a case, here is the solution to conduct this task:
- Disconnect the battery from your Toyota Venza
- Find the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever carefully on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, disconnect the holders for easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Toyota Venza, test it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have learned the main solutions for replacing license plate bulbs on your car, bear in mind that on some models the technique may be a bit different but you should be able to do it following the explanation of this article content. If you can’t do it, don’t be reluctant to go to your garage it would be a shame to break a part of your Toyota Venza. If you need to change other bulbs like the position light bulbs on your Toyota Venza or the low beam bulbs on Toyota Venza, don’t be reluctant to consult our content articles which explain you the process to follow.
To get more tips on the Toyota Venza, take a look at the Toyota Venza category.
