Regardless whether it’s for your specific safety, for roadworthiness testing or to avoid a fine, ensuring that your headlamp bulbs are constantly effective is extremely important. Indeed, bulbs are wearing parts that will predictably burn out over time and as a consequence need to be swapped out. You’re perhaps in this article because one of your parking lights is burnt out and you’re struggling with how to change your Toyota C-hr’s license plate bulb, we’ve written and published this article to help you do it all on your own and not have to go to your auto technician. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Toyota C-hr.
How to change the license plate bulb on your Toyota C-hr through the outside
This option is the most simple of the two, in truth, for this one you will just have to remove the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the situation we will dedicate some time on in the second part of this article content to clarify the way.
So let’s begin with changing the number plate bulb by going through the outside of your Toyota C-hr. Regardless whether it’s the front or the back of your vehicle the technique will be similar.
Here are a few simple actions to follow to perform this maintenance:
- With the engine off, disconnect the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to insert the flat part into the notch specified for this intent (almost always on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Toyota C-hr
- Use your screwdriver or knife to remove the bulb from its spot, if you are worried of destroying something, you can as well do it with your fingers.
- Finally, position the new license plate light bulb
- Last step, before reassembling, reconnect your battery and test the light to validate the achievement of the task.
.
How to replace the number plate bulb on your Toyota C-hr without outside access
Second part of our content, change this license plate bulb on your Toyota C-hr without external access. Most often you will be able to access it, however some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Toyota C-hr
To change the one on the front plate, nothing could be less difficult, you will have to position yourself under the vehicle (preferably placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, almost always held by two soft plastic tabs by pressing on both at the same time, then now that you have your license plate bulb block in hand, Take off the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be careful not to put in too much force otherwise you will break the plastic cover), and you will only have to remove the burnt-out license plate bulb and replace it with the new , then test and reassemble the whole thing.
How to change the rear license plate bulb on my Toyota C-hr
Finally last option, you must change the bulb on the backplate of your Toyota C-hr, but you are not able to open the cover from the outside of your vehicle. In this case, here is the technique to operate this task:
- Disconnect the battery from your Toyota C-hr
- Identify the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever softly on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, disconnect the holders for easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Toyota C-hr, test it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have learned the main tactics for changing license plate bulbs on your car, remember that on some models the method may be a bit different but you should be able to realize it following the explanation of this content. If you can’t do it, don’t hesitate to go to your workshop it would be a shame to break a part of your Toyota C-hr. If you wish to change other bulbs like the position light bulbs on your Toyota C-hr or the low beam bulbs on Toyota C-hr, don’t hesitate to consult our articles which describe you the process to follow.
If you need more tutorials on the Toyota C-hr, go to our Toyota C-hr category.
