Whether it’s for your personal security, for roadworthiness tests or to avoid a fine, ensuring that your headlamp bulbs are all the time effective is fundamental. In fact, bulbs are wearing auto parts that will predictably burn out in the future and therefore need to be changed. You’re most certainly on the website because one of your parking lights is burnt out and you’re wondering how to change your seat altea’s license plate bulb, we’ve created this document to help you do it on your own and not have to go to your mechanic. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your seat altea.
How to change the license plate bulb on your seat altea through the outside
This process is the fastest of the two, in truth, for this one you will simply require to take out the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the case we will spend some time on in the second section of this content to show you the approach.
So let’s start with replacing the number plate bulb by going through the outside of your seat altea. Whether it’s the front or the back of your motor vehicle the technique will be the same.
Here are a few simple guidelines to follow to execute this service:
- With the engine off, disconnect the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch supplied for this purpose (in most cases on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your seat altea
- Use your screwdriver or knife to remove the bulb from its placement, in the event that you are afraid of breaking anything, you can also do it with your fingers.
- Finally, put the new license plate light bulb
- Last step, before reassembling, reconnect your battery and check the light to validate the achievement of the task.
.
How to replace the number plate bulb on your seat altea without outside access
Second section of our item, swap this license plate bulb on your seat altea without external access. In most cases you will be able to access it, however some series (often at the rear does not allow this access).
How to change the front license plate bulb on my seat altea
To change the one on the front plate, nothing could be less difficult, you will have to put yourself under the motor vehicle (ideally put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in most cases held by two soft plastic tabs by pressing on both simultaneously, then right after you have your license plate bulb block in hand, Take out the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be careful not to exert too much force otherwise you will break the plastic cover), and you will only have to take out the burnt-out license plate bulb and swap it with the new , then verify and reassemble the whole thing.
How to change the rear license plate bulb on my seat altea
Finally last option, you must change the bulb on the backplate of your seat altea, but you are not able to open the cover from the outside of your motor vehicle. In this case, here is the approach to operate this operation:
- Disconnect the battery from your seat altea
- Locate the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever carefully on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, disconnect the holders for easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your seat altea, check it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have learned the main tactics for replacing license plate bulbs on your car, be aware that on some models the technique may be a bit different but you should be able to do it following the outline of this article. If you can’t do it, don’t hesitate to go to your workshop it would be a shame to break a part of your seat altea. If you want to change other bulbs like the position light bulbs on your seat altea or the low beam bulbs on seat altea, don’t hesitate to read our articles which explain you the procedure to follow.
If perhaps you have any additional questions about the seat altea, do not hesitate to consult our seat altea category.
