Regardless whether it’s for your own personal safety, for roadworthiness testing or to avoid a fine, ensuring that your headlamp bulbs are constantly functional is extremely important. Indeed, bulbs are wearing auto parts that will undoubtedly burn out after awhile and therefore need to be swapped out. You’re most likely here because one of your parking lights is burnt out and you’re struggling with how to change your Toyota Rav 4’s license plate bulb, we’ve written and published this article content to help you do it without any help and not have to go to your technician. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Toyota Rav 4.

change-license-plate-bulb-toyota-rav-4

How to replace the license plate bulb on your Toyota Rav 4 coming from the outside

This method is the most simple of the two, actually, for this one you will simply have to remove the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the case we will spend a moment on in the second section of this article to teach you the approach.
So let’s start with replacing the number plate bulb by going through the outside of your Toyota Rav 4. Regardless whether it’s the front or the back of your vehicle the operation will be similar.
Here are a few simple steps to stick to to conduct this service:

  • With the engine off, disconnect the battery terminals from your car
  • Position yourself in front of your license plate and use a flat screwdriver or knife to insert the flat part into the notch specified for this purpose (in most cases on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Toyota Rav 4
  • .

  • Use your screwdriver or knife to eject the bulb from its location, in the event that you are afraid of damaging anything, you can as well do it with your fingers.
  • Finally, put the new license plate light bulb
  • Last stage, before reassembling, reconnect your battery and verify the light to confirm the success of the task.

How to change the number plate bulb on your Toyota Rav 4 without outside access

Second section of our article, swap this license plate bulb on your Toyota Rav 4 without external access. In most cases you will be able to access it, but some series (often at the rear does not allow this access).

How to replace the front license plate bulb on my Toyota Rav 4

To replace the one on the front plate, nothing could be less complicated, you will have to put yourself under the vehicle (ideally placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in most cases kept by two soft plastic tabs by pressing on both simultaneously, then right after you have your license plate bulb block in hand, Remove the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take extra care not to put in too much force or you will break the plastic cover), and you will simply have to remove the burnt-out license plate bulb and change it with the new , then verify and reassemble the whole thing.

How to replace the rear license plate bulb on my Toyota Rav 4

Finally last solution, you must replace the bulb on the backplate of your Toyota Rav 4, but you cannot open the cover from the outside of your vehicle. In this case, here is the method to execute this operation:

  • Disconnect the battery from your Toyota Rav 4
  • Locate the position of your light bulbs from the outside.
  • From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever softly on all the frame of the trunk to remove it.
  • Once established, before removing the bulb holders, disconnect the holders for easier access.
  • Using a screwdriver, lever the two plastic parts to remove the bulb holder
  • .

  • Replace the burnt-out license plate bulb on your Toyota Rav 4, verify it and reassemble it, paying attention to the clips on the trunk liner

.
There you have it, you have discovered the main ways for replacing license plate bulbs on your car, be aware that on some models the technique may be a bit different but you should be able to do it following the explanation of this content page. If you can’t do it, don’t be reluctant to go to your mechanic it would be a shame to break a part of your Toyota Rav 4. If you need to change other bulbs like the position light bulbs on your Toyota Rav 4 or the low beam bulbs on Toyota Rav 4, don’t be reluctant to browse our content articles which demonstrate you the procedure to follow.

If you want more tutorials on the Toyota Rav 4, go to our Toyota Rav 4 category.