Regardless it’s for your own safety, for roadworthiness tests or to avoid a fine, ensuring your headlamp bulbs are all the time functioning is really important. In fact, bulbs are wearing units that will inevitably burn out in the future and consequently need to be swapped out. You’re perhaps on the website because one of your parking lights is burnt out and you’re wondering how to change your Peugeot Partner’s license plate bulb, we’ve written this content to help you do it all on your own and not have to go to your motor mechanic. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Peugeot Partner.
How to swap the license plate bulb on your Peugeot Partner throughout the outside
This process is the most simple of the two, in reality, for this one you will simply have to take away the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the situation we will dedicate some time on in the second part of this document to demonstrate the method.
So let’s begin with changing the number plate bulb by going through the outside of your Peugeot Partner. Regardless it’s the front or the back of your motor vehicle the method will be similar.
Here are a few simple steps to follow to carry out this maintenance tasks:
- With the engine off, disconnect the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch provided for this intent (usually on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Peugeot Partner
- Use your screwdriver or knife to remove the bulb from its placement, in the event you are worried of destroying anything, you can as well do it with your fingers.
- Finally, position the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and test the light to confirm the achievement of the task.
.
How to change the number plate bulb on your Peugeot Partner without outside access
Second part of our content page, change this license plate bulb on your Peugeot Partner without external access. Most often you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my Peugeot Partner
To swap the one on the front plate, nothing could be less hard, you will have to position yourself under the motor vehicle (preferably placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, usually held by two soft plastic tabs by pressing on both at once, then now that you have your license plate bulb block in hand, Take out the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take extra care not to put in too much force or you will break the plastic cover), and you will only have to take away the burnt-out license plate bulb and swap it with the new , then test out and reassemble the whole thing.
How to swap the rear license plate bulb on my Peugeot Partner
Finally last solution, you must swap the bulb on the backplate of your Peugeot Partner, but you cannot open the cover from the outside of your motor vehicle. In this instance, here is the process to carry out this task:
- Unplug the battery from your Peugeot Partner
- Locate the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever softly on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, disconnect the holders for easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Peugeot Partner, test it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have discovered the main ways for changing license plate bulbs on your car, be aware that on some models the methodology may be a bit different but you should be able to do it following the outline of this document. If you can’t do it, don’t hesitate to go to your mechanic it would be a shame to break a part of your Peugeot Partner. If you want to change other bulbs like the position light bulbs on your Peugeot Partner or the low beam bulbs on Peugeot Partner, don’t hesitate to read our content articles which describe you the operation to follow.
In the event that you have any additional questions about the Peugeot Partner, do not hesitate to consult our Peugeot Partner category.
