Whether it’s for your own security, for roadworthiness tests or to avoid a fine, being certain your headlamp bulbs are in every case functioning is very important. Indeed, bulbs are wearing auto parts that will inevitably burn out after some time and consequently need to be changed. You’re most likely on the website because one of your parking lights is burnt out and you’re wanting to know how to change your Peugeot Bipper’s license plate bulb, we’ve written and published this article content to help you do it all on your own and not have to go to your auto technician. Firstly, we will examine changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Peugeot Bipper.
How to change the license plate bulb on your Peugeot Bipper throughout the outside
This solution is the easiest of the two, in fact, for this one you will just require to take off the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the situation we will spend some time on in the second part of this article content to show you the way.
So let’s start with changing the number plate bulb by going through the outside of your Peugeot Bipper. Whether it’s the front or the back of your motor vehicle the operation will be similar.
Here are a few simple guidelines to follow to execute this maintenance tasks:
- With the engine off, unplug the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to insert the flat part into the notch specified for this purpose (in general on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Peugeot Bipper
- Use your screwdriver or knife to eject the bulb from its place, if you are afraid of damaging something, you can also do it with your fingers.
- Finally, position the new license plate light bulb
- Last step, before reassembling, reconnect your battery and check the light to validate the success of the task.
.
How to change the number plate bulb on your Peugeot Bipper without outside access
Second part of our item, swap this license plate bulb on your Peugeot Bipper without external access. Generally you will be able to access it, however some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Peugeot Bipper
To change the one on the front plate, nothing could be easier, you will have to position yourself under the motor vehicle (ideally placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in general kept by two soft plastic tabs by pressing on both at the same time, then once you have your license plate bulb block in hand, Take off the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be attentive not to put in too much pressure or you will break the plastic cover), and you will simply have to take off the burnt-out license plate bulb and swap it with the new , then verify and reassemble the whole thing.
How to change the rear license plate bulb on my Peugeot Bipper
Finally last solution, you must change the bulb on the backplate of your Peugeot Bipper, but you simply cannot open the cover from the outside of your motor vehicle. In this case, here is the method to perform this operation:
- Unplug the battery from your Peugeot Bipper
- Find the spot of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever gently on all the frame of the trunk to remove it.
- Once found, before removing the bulb holders, unplug the holders for less difficult access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Peugeot Bipper, check it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have found out the main techniques for changing license plate bulbs on your car, take note that on some models the technique may be a bit different but you should be able to realize it following the explanation of this article content. If you can’t do it, don’t hesitate to go to your garage area it would be a shame to break a part of your Peugeot Bipper. If you want to change other bulbs like the position light bulbs on your Peugeot Bipper or the low beam bulbs on Peugeot Bipper, don’t hesitate to browse our content articles which describe you the process to follow.
If you want more guides on the Peugeot Bipper, go to our Peugeot Bipper category.
