Whether it’s for your specific security, for roadworthiness testing or to avoid a fine, making sure your headlamp bulbs are constantly working is fundamental. In reality, bulbs are wearing units that will surely burn out over time and consequently need to be replaced. You’re most certainly on this website because one of your parking lights is burnt out and you’re questioning how to change your Peugeot Partner 2’s license plate bulb, we’ve written and published this article content to help you do it by yourself and not have to go to your auto mechanic. Firstly, we will take a look at changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Peugeot Partner 2.
How to change the license plate bulb on your Peugeot Partner 2 throughout the outside
This option is the fastest of the two, in reality, for this one you will just have to take out the protective covers of the bulbs. Sadly on some years or packages of car these covers do not open from the outside and if this is the case we will take a moment on in the second section of this article content to demonstrate the approach.
So let’s start with changing the number plate bulb by going through the outside of your Peugeot Partner 2. Whether it’s the front or the back of your car the operation will be similar.
Here are a few simple actions to follow to conduct this maintenance tasks:
- With the engine off, unplug the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to place the flat part into the notch supplied for this purpose (usually on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Peugeot Partner 2
- Use your screwdriver or knife to remove the bulb from its placement, in the event that you are afraid of breaking something, you can also do it with your fingers.
- Finally, position the new license plate light bulb
- Last step, before reassembling, reconnect your battery and test the light to validate the achievement of the task.
.
How to change the number plate bulb on your Peugeot Partner 2 without outside access
Second section of our content page, replace this license plate bulb on your Peugeot Partner 2 without external access. Generally you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to change the front license plate bulb on my Peugeot Partner 2
To change the one on the front plate, nothing could be less complicated, you will have to position yourself under the car (ideally positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, usually held by two soft plastic tabs by pressing on both at the same time, then right after you have your license plate bulb block in hand, Take off the plastic that works as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be careful not to apply too much pressure or you will break the plastic cover), and you will simply have to take out the burnt-out license plate bulb and replace it with the new , then test and reassemble the whole thing.
How to change the rear license plate bulb on my Peugeot Partner 2
Finally last solution, you must change the bulb on the backplate of your Peugeot Partner 2, but you simply cannot open the cover from the outside of your car. In this case, here is the method to execute this task:
- Unplug the battery from your Peugeot Partner 2
- Locate the spot of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever softly on all the frame of the trunk to remove it.
- Once located, before removing the bulb holders, unplug the holders for easier access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Peugeot Partner 2, test it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have found out the main approaches for changing license plate bulbs on your car, take note that on some models the technique may be a bit different but you should be able to realize it following the outline of this document. If you can’t do it, don’t hesitate to go to your garage area it would be a shame to break a part of your Peugeot Partner 2. If you want to change other bulbs like the position light bulbs on your Peugeot Partner 2 or the low beam bulbs on Peugeot Partner 2, don’t hesitate to browse our articles which describe you the procedure to follow.
To get more tips on the Peugeot Partner 2, take a look at the Peugeot Partner 2 category.
