Regardless whether it’s for your specific safety, for roadworthiness testing or to avoid a fine, being certain your headlamp bulbs are constantly working is really important. In fact, bulbs are wearing units that will undoubtedly burn out after some time and as a result need to be swapped out. You’re quite likely on this site because one of your parking lights is burnt out and you’re wanting to know how to change your Peugeot 807’s license plate bulb, we’ve created this content to help you do it all on your own and not have to go to your auto mechanic. Firstly, we will take a look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Peugeot 807.
How to replace the license plate bulb on your Peugeot 807 coming from the outside
This method is the easiest of the two, in fact, for this one you will simply require to take off the protective covers of the bulbs. Unfortunately on some years or packages of car these covers do not open from the outside and if this is the case we will take a moment on in the second part of this document to show you the approach.
So let’s begin with changing the number plate bulb by going through the outside of your Peugeot 807. Regardless whether it’s the front or the back of your automobile the operation will be the same.
Here are a few simple actions to stick to to conduct this routine service:
- With the engine turned off, unplug the battery terminals from your car
- Face your license plate and use a flat screwdriver or knife to insert the flat part into the notch specified for this goal (in general on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Peugeot 807
- Use your screwdriver or knife to remove the bulb from its place, in the event you are worried of destroying a thing, you can also do it with your fingers.
- Finally, put the new license plate light bulb
- Last step, before reassembling, reconnect your battery and verify the light to validate the success of the operation.
.
How to replace the number plate bulb on your Peugeot 807 without outside access
Second part of our article, swap this license plate bulb on your Peugeot 807 without external access. Most often you will be able to access it, but some series (often at the rear does not allow this access).
How to replace the front license plate bulb on my Peugeot 807
To replace the one on the front plate, nothing could be easier, you will have to put yourself under the automobile (preferably placed on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in general held by two soft plastic tabs by pressing on both at once, then once you have your license plate bulb block in hand, Take away the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (take care not to apply too much force otherwise you will break the plastic cover), and you will just have to take off the burnt-out license plate bulb and change it with the new , then check and reassemble the whole thing.
How to replace the rear license plate bulb on my Peugeot 807
Finally last possibility, you must replace the bulb on the backplate of your Peugeot 807, but you cannot open the cover from the outside of your automobile. In such a case, here is the method to do this operation:
- Disconnect the battery from your Peugeot 807
- Identify the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever delicately on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, unplug the holders for less difficult access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Replace the burnt-out license plate bulb on your Peugeot 807, verify it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have learned the main methods for changing license plate bulbs on your car, remember that on some models the technique may be a bit different but you should be able to do it following the explanation of this content page. If you can’t do it, don’t hesitate to go to your garage area it would be a shame to break a part of your Peugeot 807. If you want to change other bulbs like the position light bulbs on your Peugeot 807 or the low beam bulbs on Peugeot 807, don’t hesitate to browse our content articles which explain you the procedure to follow.
To get more tips on the Peugeot 807, take a look at the Peugeot 807 category.
