Regardless it’s for your own personal safety, for roadworthiness testing or to avoid a fine, being certain your headlamp bulbs are all the time operational is really important. In fact, bulbs are wearing auto parts that will undoubtedly burn out over time and consequently need to be changed. You’re most likely on this site because one of your parking lights is burnt out and you’re wondering how to change your Peugeot 407’s license plate bulb, we’ve written this article to help you do it without any help and not have to go to your mechanic. Firstly, we will take a look at changing the license plate bulb from the outside, secondly, how to replace the license plate bulb without outside access, and thirdly, how to replace the rear license plate bulb of your Peugeot 407.
How to swap the license plate bulb on your Peugeot 407 throughout the outside
This tactic is the most simple of the two, in fact, for this one you will just require to take away the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the situation we will spend some time on in the second section of this document to clarify the way.
So let’s start with changing the number plate bulb by going through the outside of your Peugeot 407. Regardless it’s the front or the back of your vehicle the technique will be the same.
Here are a few simple steps to follow to perform this service:
- With the engine turned off, unplug the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to insert the flat part into the notch supplied for this intent (in most cases on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Peugeot 407
- Use your screwdriver or knife to remove the bulb from its placement, if you are scared of damaging anything, you can also do it with your fingers.
- Finally, put the new license plate light bulb
- Last stage, before reassembling, reconnect your battery and test the light to validate the success of the process.
.
How to replace the number plate bulb on your Peugeot 407 without outside access
Second section of our content page, change this license plate bulb on your Peugeot 407 without external access. Generally you will be able to access it, nevertheless some series (often at the rear does not allow this access).
How to swap the front license plate bulb on my Peugeot 407
To swap the one on the front plate, nothing could be less difficult, you will have to put yourself under the vehicle (preferably put on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, in most cases held by two soft plastic tabs by pressing on both at the same time, then right after you have your license plate bulb block in hand, Take out the plastic that operates as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be cautious not to exert too much pressure or you will break the plastic cover), and you will simply have to take away the burnt-out license plate bulb and change it with the new , then test and reassemble the whole thing.
How to swap the rear license plate bulb on my Peugeot 407
Finally last possibility, you must swap the bulb on the backplate of your Peugeot 407, but you cannot really open the cover from the outside of your vehicle. In this case, here is the tactic to execute this task:
- Disconnect the battery from your Peugeot 407
- Identify the position of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, held by clips, you will have to lever carefully on all the frame of the trunk to remove it.
- Once located, before removing the bulb holders, unplug the holders for less complicated access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Peugeot 407, test it and reassemble it, paying attention to the clips on the trunk liner
.
.
There you have it, you have learned the main solutions for changing license plate bulbs on your car, be aware that on some models the technique may be a bit different but you should be able to accomplish it following the explanation of this document. If you can’t do it, don’t hesitate to go to your mechanic it would be a shame to break a part of your Peugeot 407. If you desire to change other bulbs like the position light bulbs on your Peugeot 407 or the low beam bulbs on Peugeot 407, don’t hesitate to browse our content articles which demonstrate you the process to follow.
Whenever you have any additional questions about the Peugeot 407, do not hesitate to consult our Peugeot 407 category.
