It doesn’t matter if it’s for your personal safety, for roadworthiness tests or to avoid a fine, being certain your headlamp bulbs are all the time effective is really important. Indeed, bulbs are wearing auto parts that will inevitably burn out over time and consequently need to be replaced. You’re most certainly on this website because one of your parking lights is burnt out and you’re wondering how to change your Jeep Liberty’s license plate bulb, we’ve written this article content to help you do it on your own and not have to go to your auto mechanic. Firstly, we will look at changing the license plate bulb from the outside, secondly, how to change the license plate bulb without outside access, and thirdly, how to change the rear license plate bulb of your Jeep Liberty.
How to replace the license plate bulb on your Jeep Liberty coming from the outside
This technique is the least difficult of the two, in fact, for this one you will simply need to take off the protective covers of the bulbs. Regrettably on some years or packages of car these covers do not open from the outside and if this is the situation we will dedicate some time on in the second section of this article content to demonstrate the way.
So let’s start with replacing the number plate bulb by going through the outside of your Jeep Liberty. It doesn’t matter if it’s the front or the back of your automobile the technique will be identical.
Here are a few simple steps to follow to perform this maintenance tasks:
- With the engine turned off, unplug the battery terminals from your car
- Position yourself in front of your license plate and use a flat screwdriver or knife to place the flat part into the notch assigned for this intent (commonly on the transparent cover) and lever on the plastic window to open the license plate bulb slot of your Jeep Liberty
- Use your screwdriver or knife to remove the bulb from its placement, if you are scared of destroying something, you can also do it with your fingers.
- Finally, position the new license plate light bulb
- Last step, before reassembling, reconnect your battery and check the light to validate the success of the procedure.
.
How to change the number plate bulb on your Jeep Liberty without outside access
Second section of our content, change this license plate bulb on your Jeep Liberty without external access. Generally you will be able to access it, however some series (often at the rear does not allow this access).
How to replace the front license plate bulb on my Jeep Liberty
To replace the one on the front plate, nothing could be less hard, you will have to position yourself under the automobile (ideally positioned on candles to give you some space), and, going through the rear of the bumper, you will have to unclip the license plate bulb block, commonly kept by two soft plastic tabs by pressing on both simultaneously, then right after you have your license plate bulb block in hand, Take out the plastic that acts as a seal, then with a thin screwdriver, on one side you will find a small notch, use a lever to open the plastic cover (be attentive not to exert too much pressure otherwise you will break the plastic cover), and you will simply have to take off the burnt-out license plate bulb and replace it with the new , then verify and reassemble the whole thing.
How to replace the rear license plate bulb on my Jeep Liberty
Finally last option, you must replace the bulb on the backplate of your Jeep Liberty, but you cannot open the cover from the outside of your automobile. In this case, here is the method to carry out this operation:
- Disconnect the battery from your Jeep Liberty
- Find the location of your light bulbs from the outside.
- From the inside of the trunk, you have to remove the lining of the trunk, kept by clips, you will have to lever gently on all the frame of the trunk to remove it.
- Once established, before removing the bulb holders, unplug the holders for less complicated access.
- Using a screwdriver, lever the two plastic parts to remove the bulb holder
- Change the burnt-out license plate bulb on your Jeep Liberty, check it and reassemble it, watching the clips on the trunk liner
.
.
There you have it, you have learned the main ways for replacing license plate bulbs on your car, take notice that on some models the methodology may be a bit different but you should be able to do it following the outline of this article content. If you can’t do it, don’t hesitate to go to your garage area it would be a shame to break a part of your Jeep Liberty. If you need to change other bulbs like the position light bulbs on your Jeep Liberty or the low beam bulbs on Jeep Liberty, don’t hesitate to browse our content articles which demonstrate you the procedure to follow.
If you wish more guides on the Jeep Liberty, go to our Jeep Liberty category.
